Diffuser - Options!!!!
#1
Diffuser - Options!!!!
I really don't like the plain look of the diffuser on my 2012 XF portfolio. Just for a simple cosmetic mode,
spending way too much time and money to pull the existing one and putting a new diffuser ( close to $500 to $1000) is also worthless in IMHO.
Wanted to get your thoughts from you folks...... I am thinking of putting this with double sided 3M tapes to the existing diffuser ( rather than screwing it on so that I can take it off if needed.....will screw it on later if I like the looks). Also plast dip the whole diffuser along with this trim kit. I can even have Carbon fiber plasti dip
Rear Bumper Diffuser Molding Point Garnish Trim Matt Black for JAGUAR Car | eBay
Well, its not going to look that great but how bad it can get? ....Overall cost wise is very less and can be taken off if I dont like it..
What do you all think?I am ready with my full body armour suit ( just in case I need it here)
spending way too much time and money to pull the existing one and putting a new diffuser ( close to $500 to $1000) is also worthless in IMHO.
Wanted to get your thoughts from you folks...... I am thinking of putting this with double sided 3M tapes to the existing diffuser ( rather than screwing it on so that I can take it off if needed.....will screw it on later if I like the looks). Also plast dip the whole diffuser along with this trim kit. I can even have Carbon fiber plasti dip
Rear Bumper Diffuser Molding Point Garnish Trim Matt Black for JAGUAR Car | eBay
Well, its not going to look that great but how bad it can get? ....Overall cost wise is very less and can be taken off if I dont like it..
What do you all think?I am ready with my full body armour suit ( just in case I need it here)
Last edited by aparanschumi; 01-21-2017 at 10:34 AM. Reason: photos
#2
The xfr diffuser can be used, is a couple hundred, and already painted.
Easy DIY...
https://parts.elderautogroup.com/oem...FQYOaQod-9sPsw
https://m.youtube.com/watch?v=InyQVxUGYkA
Easy DIY...
https://parts.elderautogroup.com/oem...FQYOaQod-9sPsw
https://m.youtube.com/watch?v=InyQVxUGYkA
Last edited by Shadow993; 01-21-2017 at 01:52 PM.
#4
#5
#6
#7
Trending Topics
#8
no. I contacted Mina a week ago asking the same question. At the moment they do not sell the diffuser. Have been trying to get them to send me a picture of the front splitter for the XF Sport with no luck. The picture they provide is pretty vauge. I want to see the entire splitter to see how it will attach. I already know they say it sticks on with 3M tape. I want to see the whole part. Wish they would send me a freaking photo.
#9
Join Date: Feb 2014
Location: Adelaide, South Australia
Posts: 8,291
Received 3,114 Likes
on
2,297 Posts
#10
They do that with products from time to time. I picked up a carbon engine cover that they made only a few of and discontinued.
#12
#15
#16
no. I contacted Mina a week ago asking the same question. At the moment they do not sell the diffuser. Have been trying to get them to send me a picture of the front splitter for the XF Sport with no luck. The picture they provide is pretty vauge. I want to see the entire splitter to see how it will attach. I already know they say it sticks on with 3M tape. I want to see the whole part. Wish they would send me a freaking photo.
Here are the Mina front splitters in carbon, and the rear valance they had offered. (Ignore the sport badge, gone now. I wanted to put something on the back without posing but decided to take off)
The rear valance was a nightmare to install. It was fiberglass and simply had no flexibility so it took a lot of rigging. I eventually had to uses a gasket caulk to fill poor fit. Oddly it turned out pretty good. Even used aftermarket touch up spray paint to paint the lunar gray.
The front splitters (different for the R and S I believe but same install) are much easier but PLEASE!!!!!! add some stainless screws under it. I lost two on interstate driving. 3m tape is not strong enough at highway speeds.
Yes, I have extensivly modified my cat to my taste so, please, no negative comments. It's my hobby and I do try to keep it tasteful but my inner chav must have a chance! Lol. (Oh, and I LOVED it when Jaguar added the spoiler to the F-type. Very similar to my carbon aftermarket one! Before that, people said it was wrong! Now they say Wow! Looks like the F-type new spoiler! Lol)
#17
That's exactly what I am scared of. The prospect of having my splitters dropping when going at freeway speeds is not something that I will put my self through. That is why I have been asking Mina to send me photos of their splitters not installed, but just on a table or something, so I can see how to best attach them. I am not purchasing them until I see them unattached. Do you happen to have any photos of the splitters?? I notice you de-chromed your Jag..looks nice. What did you use to wrap with? I have been looking for a place that does carbon fiber wrap, but have only found the vinyl stuff..
#18
#19
Here is my front splitter that I made.
https://www.jaguarforums.com/g/picture/2890062
https://www.jaguarforums.com/g/picture/2890061
I am not sure why I could not get the pics to load up automatically.
I just changed it and replaced it with ones that have the side winglets. I will post pics of those tomorrow.
https://www.jaguarforums.com/g/picture/2890062
https://www.jaguarforums.com/g/picture/2890061
I am not sure why I could not get the pics to load up automatically.
I just changed it and replaced it with ones that have the side winglets. I will post pics of those tomorrow.
Last edited by Mr Sharky; 01-30-2017 at 03:56 AM.