Jaguar Forums - Jaguar Enthusiasts Forum - Search Results

 
Search: Posts Made By: katar83
Showing results 1 to 25 of 37
Search took 0.26 seconds.
06-25-2019, 10:42 PM
Replies: 5
Views: 1,032
Posted By SleekJag12

The ports used in the x300 are GM style ball...

The ports used in the x300 are GM style ball valve ports, used on literally hundreds of millions of GM cars and trucks. Any recharge kit that lists a lot of older R134 GM vehicles will likely fit. An...
Forum: XJ40 ( XJ81 )
05-29-2019, 10:54 PM
Replies: 5
Views: 2,020
Posted By retroren

Installing '93 door cards on a '91

https://cimg5.ibsrv.net/gimg/www.jaguarforums.com-vbulletin/2000x1504/img_0186_1__a0a05dd323b68a72223957aa7408bfb645db1ba0.jpg
My desire to get rid of my tiny 3.5" front door speakers and jump to...
Forum: XJS ( X27 )
05-01-2019, 06:31 PM
Replies: 28
Views: 721
Posted By orangeblossom

MGB Update Took off the Brake Drums to Free...

MGB Update

Took off the Brake Drums to Free off the Hubs which was a nightmare job to do in such a confined space but that was nothing compared to trying to put them back which was really the kind...
04-28-2019, 05:11 AM
Replies: 18
Views: 1,171
Posted By Marc-XJ12

Looking at the ring gear they both have the same...

Looking at the ring gear they both have the same diameter, tooth count and sit at the same depth in the hub carrier! Also a quick check on jag classic parts they share the same part no. CBC4705

I...
04-22-2019, 02:35 PM
Replies: 9
Views: 553
Posted By Don B

Hi Ash, Those braided cables are...

Hi Ash,

Those braided cables are ground/earth straps that help protect the wheel bearings from erosion due to electrical currents and static electric accumulation and discharge.

See pdf page 21...
Forum: XJS ( X27 )
03-04-2019, 12:25 AM
Replies: 6
Views: 461
Posted By warrjon

You can not bleed the rear brakes by pumping the...

You can not bleed the rear brakes by pumping the pedal, it WILL NOT work.

My procedure.
1 Pump the sprayer up and bleed all the brakes start at the rear left, open the nipple. Careful to ensure...
02-17-2019, 07:33 PM
Replies: 2
Views: 514
Posted By Don B

Hi John, Your understanding is correct. You...

Hi John,

Your understanding is correct. You just unbolt the axle from the output shaft flange and set or tie the axle aside for clearance, then remove the screws that attach the seal flange to the...
02-17-2019, 11:04 AM
Replies: 30
Views: 3,743
Posted By mckarlas

Almost there... ...

Almost there...

https://cimg5.ibsrv.net/gimg/www.jaguarforums.com-vbulletin/2000x1504/remotebatterycover_8a49bbf9738bcbfcf7faf313f97243521bcfaf42.jpg
Forum: XJS ( X27 )
10-21-2018, 10:16 PM
Replies: 11
Views: 4,287
Posted By afterburner1

Years ago I had a plastic windshield made for a...

Years ago I had a plastic windshield made for a "69 Lotus Elite. Although it fit well the distortion looking though it was severe. I was through with the body work, but the car still required paint....
10-10-2018, 02:22 PM
Replies: 6
Views: 547
Posted By Sheff928

Try adapting this method to connectors? You...

Try adapting this method to connectors?
You might be able to use a spray bottle.
https://www.instructables.com/id/How-to-perfectly-clean-wires-in-minutes/
09-17-2018, 07:06 PM
Replies: 17
Views: 857
Posted By Lady Penelope

The key is weither there is a servicing port (...

The key is weither there is a servicing port ( shrader valve in which yo inject the mitrogen to a measured value of stated between 180 and 200 psi with no wheit on the wheel as a assembly .

The...
04-28-2018, 06:18 AM
Replies: 10
Views: 752
Posted By Richardhw

The diff bolts through the lower subframe I get...

The diff bolts through the lower subframe I get to be M12x 1.25pitch 20mm long,
got mine out at the moment so just measured them, grade 8.8 so should be easily available.
04-20-2018, 07:33 PM
Replies: 147
Views: 9,793
Posted By Lady Penelope

A clogged fuel filter will eventually show full...

A clogged fuel filter will eventually show full fuel pressure after a while if you have the output capped . Just won't deliver pressure / volume amount . With the return open to the tank there is the...
04-20-2018, 07:18 PM
Replies: 147
Views: 9,793
Posted By Jagboi64

Definitely a bad regulator. I'd change the fuel...

Definitely a bad regulator. I'd change the fuel filter too, just on general principals.
03-08-2018, 10:19 PM
Replies: 15
Views: 1,623
Posted By John Herbert

Regarding your continued search Al for a...

Regarding your continued search Al for a suitable tee for your fuel rail may I suggest you investigate a M14x1.5 metric extension with 1/8 npt port as shown in the attachment.
This part is made...
Forum: XJS ( X27 )
02-22-2018, 10:09 AM
Replies: 54
Views: 2,659
Posted By Greg in France

Make sure the actual car is on solid ground...

Make sure the actual car is on solid ground before you start jacking anything; if not, then there MUST be very solid very wide and long plates under all the load bearing structures (jacks and...
Forum: XJS ( X27 )
02-22-2018, 07:28 AM
Replies: 54
Views: 2,659
Posted By Greg in France

Paul With no lift it is still doable on your...

Paul
With no lift it is still doable on your own. I did mine that way 18 years ago for the first time. Basically this is the procedure I followed:

Loosen but do not remove the rear wheelnuts
...
Forum: XJS ( X27 )
02-14-2018, 03:32 AM
Replies: 33
Views: 2,318
Posted By Grant Francis

From Downunder, where the roads are unsealed,...

From Downunder, where the roads are unsealed, corrugated, large dust holes (Wombat nests), and generally Un-Jaguar style.

I use Poly on the rack and the sway bar "D ONLY.

Tried Poly on the top...
02-06-2018, 07:49 PM
Replies: 4
Views: 778
Posted By Lady Penelope

Yes mine is capped off at the nipple just fwd of...

Yes mine is capped off at the nipple just fwd of the fuel pressure regulator intake manifold nipple . Looks like a factory cap . Might have something to do with the fuel EVAP system as there are 2...
02-05-2018, 04:29 PM
Replies: 24
Views: 1,314
Posted By Lady Penelope

I'm just saying , ...

I'm just saying ,

https://www.jaguarclassicparts.com/uk/jaguar-xj-x300-parts

http://www.jagrepair.com/images/Training%20Guides/801S%20-%202000.pdf
...
01-26-2018, 09:35 AM
Replies: 11
Views: 1,648
Posted By Don B

It is very important to not reuse the original...

It is very important to not reuse the original axle nuts. They are designed with a helical insert that deforms when the nut is subjected to the final torque of more than 200 lb. ft. The helical...
01-25-2018, 05:12 PM
Replies: 11
Views: 1,648
Posted By JBzXJ40

Just a recommendation, but I would replace the...

Just a recommendation, but I would replace the axle nut as well , up to you. Don't forget to lube the axle shaft inside the wheel hub as well.
01-25-2018, 05:09 PM
Replies: 11
Views: 1,648
Posted By JBzXJ40

Yes have replaced these before. A little involved...

Yes have replaced these before. A little involved but not too bad of a job. If you're only doing the u joints on one axle, may as well do both u joints. Otherwise you'll have to take the axle back...
01-20-2018, 06:09 PM
Replies: 9
Views: 538
Posted By NBCat

If you are looking for the front bumper undertray...

If you are looking for the front bumper undertray for an X300, the JLR part number is: BEC19939. There is also a fitting kit: BEC19939KIT.

Both are most likely available from a local Jaguar...
12-18-2017, 08:51 AM
Replies: 26
Views: 1,515
Posted By Doug

Katar, there are various ways to skin a cat :) ...

Katar, there are various ways to skin a cat :)

No harm in going right to the cable, I reckon. If it's visibly/obviously loose it obviously needs to be tightened.

And in reality there's no...
Showing results 1 to 25 of 37
 


 
Forum Jump

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service

© 2019 MH Sub I, LLC dba Internet Brands

We are a participant in the Amazon Services LLC Associates Program, an affiliate advertising program designed to provide a means for us to earn fees by linking to Amazon.com and affiliated sites.