Jaguar Forums - Jaguar Enthusiasts Forum
Share Your Pictures with Our Community. Upload Now
0 2022/12/07 23:29:56
0 2022/12/07 23:29:45
0 2022/12/07 20:41:36
0 2022/12/07 19:16:13
0 2022/12/07 19:16:07
0 2022/12/07 19:16:03
0 2022/12/07 17:51:06
0 2022/12/07 17:27:47
0 2022/12/07 16:35:55
0 2022/12/07 16:21:25
0 2022/12/07 16:21:23
0 2022/12/07 16:09:20
Advertisement
With all the spotwelds removed there will be a paint line that I can use as a reference to how far up the sides I need to come, and then fill in the holes where the spotweld were and seal it all up when I have finished welding it all out.
With all the spotwelds removed there will be a paint line that I can use as a reference to how far up the sides I need to come, and then fill in the holes where the spotweld were and seal it all up when I have finished welding it all out.
0 2022/12/07 12:22:03
I have decided to drill out all the spotwelds I can, and then using a 5 inch grinder with a 1mm cutting disk remove the walls or this boot interior.
I have decided to drill out all the spotwelds I can, and then using a 5 inch grinder with a 1mm cutting disk remove the walls or this boot interior.
0 2022/12/07 12:20:30
I have decided that I will cut away the sheetmetal all the way up to the top of the rear section here, and then lighning up all the reference point I have (not clearly marked for you to see).
I have decided that I will cut away the sheetmetal all the way up to the top of the rear section here, and then lighning up all the reference point I have (not clearly marked for you to see).
0 2022/12/07 12:17:44
With all the welds sealed with a bitument type of sealer, it is almost ready to be fitted to the car, the thing I will need to do next is prepare the car for the floor to be welded in.
With all the welds sealed with a bitument type of sealer, it is almost ready to be fitted to the car, the thing I will need to do next is prepare the car for the floor to be welded in.
0 2022/12/07 12:15:44
This is the cutout before the sheetmetal was installed. I simply need to make this side the same as the other side and it will be ready to install into the green car.
This is the cutout before the sheetmetal was installed. I simply need to make this side the same as the other side and it will be ready to install into the green car.
0 2022/12/07 12:13:59
Here we can see the cutout i was talking about. The white section is a bit of sheet metal I had lying around, it is a tad heavier than the original metal, making it a little easier to weld.
Here we can see the cutout i was talking about. The white section is a bit of sheet metal I had lying around, it is a tad heavier than the original metal, making it a little easier to weld.
0 2022/12/07 12:11:44
Here we can see where the original exhaust outlet is. Here I am going to make a cutout in the boot floor before I re install it. This should allow me to fit the exhaust I want to the rear of the car.
Here we can see where the original exhaust outlet is. Here I am going to make a cutout in the boot floor before I re install it. This should allow me to fit the exhaust I want to the rear of the car.
0 2022/12/07 12:09:46
I have already removed the floor here, but this is one of those places that limits us from doing anything to the rear of the car. I am looking to fit a twinn exhaust outlet, and the original boot floor makes this rather hard.
I have already removed the floor here, but this is one of those places that limits us from doing anything to the rear of the car. I am looking to fit a twinn exhaust outlet, and the original boot floor makes this rather hard.
0 2022/12/07 12:07:11
0 2022/12/07 12:05:56
0 2022/12/07 12:05:49
0 2022/12/07 12:05:46
0 2022/12/07 12:05:40
0 2022/12/07 12:05:36
0 2022/12/07 12:05:28
0 2022/12/07 10:35:07
0 2022/12/07 10:27:35
0 2022/12/07 10:27:28
0 2022/12/07 10:27:21
0 2022/12/07 10:27:14
0 2022/12/07 10:27:07
Advertisement