Jaguar Forums - Jaguar Enthusiasts Forum
Share Your Pictures with Our Community. Upload Now
0 2021/06/03 14:28:23
0 2021/06/03 13:42:02
0 2021/06/03 13:41:31
0 2021/06/03 13:00:54
On the 7 inch screen - mote on the left, the control panel remains connected and the white connector doesn't exist as it the flasher button and resistor attached to the large screen fascia.
On the 7 inch screen - mote on the left, the control panel remains connected and the white connector doesn't exist as it the flasher button and resistor attached to the large screen fascia.
0 2021/06/03 12:58:24
0 2021/06/03 11:55:39
0 2021/06/03 11:55:35
I took a Majic Marker and marked the edge of the overlap so that I could measure aft from that line when placing the hole.
I took a Majic Marker and marked the edge of the overlap so that I could measure aft from that line when placing the hole.
0 2021/06/03 11:51:25
Both sections of the undertray removed. Only the rear section needs to be removed to cut the hole.You can see the centerline fore and aft that you need to measure from
Both sections of the undertray removed. Only the rear section needs to be removed to cut the hole.You can see the centerline fore and aft that you need to measure from
0 2021/06/03 11:51:24
View of factory oil pan drain plug
View of factory oil pan drain plug
0 2021/06/03 11:51:22
0 2021/06/03 11:51:20
Photo of Fumoto valve. You can push a short length of hose over the end to drain the oil and keep it out of the undertray.
Photo of Fumoto valve. You can push a short length of hose over the end to drain the oil and keep it out of the undertray.
0 2021/06/03 11:51:18
Advertisement
0 2021/06/03 11:51:17
0 2021/06/03 11:51:15
The dimensions for where I should have placed the hole in the under tray.
The dimensions for where I should have placed the hole in the under tray.
0 2021/06/03 11:51:13
Fumoto valve installed
Fumoto valve installed
0 2021/06/03 11:51:11
Photo of the undertray installed. As you can see I should have placed the hole about 2" further right and about 2"-3" further toward the rear to center the valve in the hole.
Photo of the undertray installed. As you can see I should have placed the hole about 2" further right and about 2"-3" further toward the rear to center the valve in the hole.
0 2021/06/03 11:51:10
Photo shows the 5" diameter hole cut in the undertray with the tray removed.
Photo shows the 5" diameter hole cut in the undertray with the tray removed.
0 2021/06/03 11:51:07
0 2021/06/03 11:47:01
0 2021/06/03 11:46:59
0 2021/06/03 11:46:57
0 2021/06/03 11:46:56
0 2021/06/03 11:46:54
0 2021/06/03 11:46:52
0 2021/06/03 11:46:51
0 2021/06/03 11:46:49
View of the Fumoto valve installed.
View of the Fumoto valve installed.
0 2021/06/03 11:46:47
As you can see, it would have been better to move the hole about 2" further right and about 2-3 inches further aft.
As you can see, it would have been better to move the hole about 2" further right and about 2-3 inches further aft.
0 2021/06/03 11:46:45
5" diameter hole cut in the undertray
5" diameter hole cut in the undertray
0 2021/06/03 11:46:43
0 2021/06/03 11:00:12
0 2021/06/03 10:59:35
0 2021/06/03 10:49:15
Advertisement