Jaguar Forums - Jaguar Enthusiasts Forum
Share Your Pictures with Our Community. Upload Now
0 2016/07/04 20:22:25
0 2016/07/04 19:01:23
0 2016/07/04 18:49:43
0 2016/07/04 18:04:06
0 2016/07/04 18:04:01
0 2016/07/04 18:03:52
0 2016/07/04 18:03:46
0 2016/07/04 18:03:41
0 2016/07/04 18:03:36
Show of Dreams - British Cars of New Hampshire
Show of Dreams - British Cars of New Hampshire
0 2016/07/04 17:49:47
Proud owner of a Jaguar X-Type Sportswagon
Proud owner of a Jaguar X-Type Sportswagon
0 2016/07/04 17:49:46
Show of Dreams Car Show British Cars of New Hampshire
Show of Dreams Car Show British Cars of New Hampshire
0 2016/07/04 17:49:45
Advertisement
0 2016/07/04 17:28:26
I filed a flat on the end of the rod so I could center punch for the cross hole. I drilled a 15/64" hole 1st then a 1/4" hole and had a nice tight slip fit.
I filed a flat on the end of the rod so I could center punch for the cross hole. I drilled a 15/64" hole 1st then a 1/4" hole and had a nice tight slip fit.
0 2016/07/04 16:55:16
1 pair of self aligning washers, spherical faces go against each other, flat faces face out, 2 pairs back to back on each compressor
1 pair of self aligning washers, spherical faces go against each other, flat faces face out, 2 pairs back to back on each compressor
0 2016/07/04 16:55:15
2 different size washers, big ones go against the bottom of the spring pan
2 different size washers, big ones go against the bottom of the spring pan
0 2016/07/04 16:55:14
fuzzy picture showing dowel centerline ~5/8" below end of rod (3/4" didn't fit)
fuzzy picture showing dowel centerline ~5/8" below end of rod (3/4" didn't fit)
0 2016/07/04 16:55:13
both compressors side by side, showing order of assy
both compressors side by side, showing order of assy
0 2016/07/04 16:55:11
0 2016/07/04 16:53:55
0 2016/07/04 16:49:48
I filed a flat on the end of the threaded rod so I could center punch for the cross hole. I drilled thru with a 15/64" bit 1st then 1/4" and it gave me a nice tight slip fit for the dowel
I filed a flat on the end of the threaded rod so I could center punch for the cross hole. I drilled thru with a 15/64" bit 1st then 1/4" and it gave me a nice tight slip fit for the dowel
0 2016/07/04 16:41:57
1 pair of self aligning washers, spherical faces face each other, 2 pairs back to back, flat faces face out on each pair
1 pair of self aligning washers, spherical faces face each other, 2 pairs back to back, flat faces face out on each pair
0 2016/07/04 16:41:53
2 different size washers, big ones go against the bottom of the spring pan
2 different size washers, big ones go against the bottom of the spring pan
0 2016/07/04 16:41:47
fuzzy picture but shows the dowel center line ~ 5/8" below end of threaded rod (3/4" wouldn't fit)
fuzzy picture but shows the dowel center line ~ 5/8" below end of threaded rod (3/4" wouldn't fit)
0 2016/07/04 16:41:41
both compressors side by side, one assembled, 2nd showing the order of assy
both compressors side by side, one assembled, 2nd showing the order of assy
0 2016/07/04 16:41:35
0 2016/07/04 16:10:15
ok I used a 1 inch mirror.... that is going to be fun...
ok I used a 1 inch mirror.... that is going to be fun...
0 2016/07/04 15:14:28
at the cut off angle
at the cut off angle
0 2016/07/04 15:14:07
yeap
yeap
0 2016/07/04 15:13:42
0 2016/07/04 13:20:41
0 2016/07/04 13:20:34
0 2016/07/04 13:20:02
Advertisement