Jaguar Forums - Jaguar Enthusiasts Forum
R134a High pressure HLPS switch
R134a High pressure HLPS switch
0 2019/06/24 13:15:11
30-40 degree additional angle at present hing attach point
30-40 degree additional angle at present hing attach point
0 2019/06/25 12:47:49
Attach Bracket: One piece per side, replaced with combination attach bracket/secondary hinge & spring....
Attach Bracket: One piece per side, replaced with combination attach bracket/secondary hinge & spring....
0 2019/06/25 13:11:17
Factory Hinge attach Bracket
Factory Hinge attach Bracket
0 2019/06/28 16:59:01
Jeff's secondary hold-open rod
Jeff's secondary hold-open rod
0 2019/06/28 16:59:38
Proposed Bracket Hinge combination +30 degrees
Proposed Bracket Hinge combination +30 degrees
0 2019/06/28 17:00:11
13" 2x4
13" 2x4
0 2019/07/05 18:31:57
37-1/2-38" prop
37-1/2-38" prop
0 2019/07/05 18:32:07
First mock-up of new hinge/bracket (Friction lock is for proto-type only)
First mock-up of new hinge/bracket (Friction lock is for proto-type only)
0 2019/07/05 18:32:20
OEM opening
OEM opening
0 2019/07/05 18:32:37
14 degree increase of targeted 30
14 degree increase of targeted 30
0 2019/07/05 18:35:25
13" 2x4
13" 2x4
0 2019/07/05 18:39:44
37-1/2 to 38" prop
37-1/2 to 38" prop
0 2019/07/05 18:39:53
First mock-up of Hinge/Bracket (friction knob lock is for prototype only)
First mock-up of Hinge/Bracket (friction knob lock is for prototype only)
0 2019/07/05 18:40:05
OEM opening
OEM opening
0 2019/07/05 18:40:13
13-1/2 degree increased opening ~7.5"
13-1/2 degree increased opening ~7.5"
0 2019/07/05 18:40:19
0 2019/07/08 13:56:27
68 degree opening with modified hinge/bracket
68 degree opening with modified hinge/bracket
0 2019/07/13 17:57:38
0 2019/07/13 17:59:03
OEM config> one 24" x 40 lbs strut (aft end not secured...has bracket for two screws)
OEM config> one 24" x 40 lbs strut (aft end not secured...has bracket for two screws)
0 2019/07/13 17:59:21
OEM config>Fwd end attached to existing 5/16" hole in Hinge arm. One strut reached this height with out assistance
OEM config>Fwd end attached to existing 5/16" hole in Hinge arm. One strut reached this height with out assistance
0 2019/07/13 18:00:02
0 2019/07/15 11:57:01
Confirm the ignition switch wires are correct, with Ign SW off, there should be no PWR to + side of Coil
Confirm the ignition switch wires are correct, with Ign SW off, there should be no PWR to + side of Coil
0 2019/07/17 03:50:51
Projected Combination Hinge/Bracket LH & RH
Projected Combination Hinge/Bracket LH & RH
0 2019/07/23 21:02:17
Full open..69 degrees, hands free. two 11" struts mounted to OEM hinge arm
Full open..69 degrees, hands free. two 11" struts mounted to OEM hinge arm
0 2019/07/23 21:02:36
Single Strut Spring Assist.
Single Strut Spring Assist.
0 2019/07/23 21:02:53
Optional cover for Spring Assist strut
Optional cover for Spring Assist strut
0 2019/07/23 21:07:37
0 2019/07/23 21:12:03
0 2019/07/23 21:25:26
Full extension of 11" Strut on S3
Full extension of 11" Strut on S3
0 2019/07/27 12:03:45
Height of attach hole in OEM hinge arm S3
Height of attach hole in OEM hinge arm S3
0 2019/07/27 12:03:58
On intake manifold below red arrow
On intake manifold below red arrow
0 2019/07/28 17:19:00
7/32 Allen wrench with a little propane heat and a vice to bend into position.
7/32 Allen wrench with a little propane heat and a vice to bend into position.
0 2019/07/28 23:07:14
Center line of Bolt to C.L. of Hole
Center line of Bolt to C.L. of Hole
0 2019/08/01 11:37:21
C.L. of hole to Trunk shelf
C.L. of hole to Trunk shelf
0 2019/08/01 11:37:30
Fitting on Water Pump
Fitting on Water Pump
0 2019/08/04 13:40:54
Red Heater Valve, Bottom fitting on Firewall Green Vac to A/C , goes to top fitting on Firewall
Red Heater Valve, Bottom fitting on Firewall Green Vac to A/C , goes to top fitting on Firewall
0 2019/08/05 11:20:56
Probably #10 wire to battery post would be fine for the distance you have. Your Tach maybe off + side of coil.
Probably #10 wire to battery post would be fine for the distance you have. Your Tach maybe off + side of coil.
0 2019/08/05 16:57:06
S3: from trunk ledge to arm hole 11-1/4 inches
S3: from trunk ledge to arm hole 11-1/4 inches
0 2019/08/05 19:38:23
Hinge/Bracket kit (LH)
Hinge/Bracket kit (LH)
0 2019/08/28 17:56:30