Jaguar Forums - Jaguar Enthusiasts Forum
0 2023/02/11 19:44:17
0 2023/02/13 16:20:39
0 2023/03/17 12:55:42
0 2023/03/26 02:00:03
0 2023/03/26 02:00:12
0 2023/03/26 02:00:20
0 2023/03/26 02:01:19
0 2023/03/26 02:02:01
Fully installed with XJ40 gaskets
Fully installed with XJ40 gaskets
0 2023/05/16 02:08:58
Showing the Mustang Coyote coils I’ve posted about before .
Showing the Mustang Coyote coils I’ve posted about before .
0 2023/05/16 02:09:06
A bit of skill needed to drill and tap the cam cover in the groove for the m6 stud that holds the coils down.
A bit of skill needed to drill and tap the cam cover in the groove for the m6 stud that holds the coils down.
0 2023/05/16 02:09:14
The baffle has been removed cleaned and reinstalled with 2x diameter M6 flange bolts , lock tite high strength and torqued with an 1/4 drive torque wrench .
The baffle has been removed cleaned and reinstalled with 2x diameter M6 flange bolts , lock tite high strength and torqued with an 1/4 drive torque wrench .
0 2023/05/16 02:09:21
The setup to drill and tap out the fixings for the baffle .
The setup to drill and tap out the fixings for the baffle .
0 2023/05/16 02:09:29
Developing the coil cover plate .
Developing the coil cover plate .
0 2023/05/16 02:09:32
Some hands on paper templates before taking it to fusion 360z
Some hands on paper templates before taking it to fusion 360z
0 2023/05/16 02:09:39
0 2023/09/23 04:02:24
0 2023/09/23 04:02:39
0 2023/09/23 04:02:51
0 2023/09/23 04:03:02
0 2023/09/23 04:03:21
0 2023/09/23 04:03:36
0 2023/09/23 04:03:40
0 2023/09/23 04:15:02
0 2023/09/23 04:15:05
This template is to become a 3mm stainless steel profile cut piece which bolts to the casting to “put back” the missing pivot tab .
This template is to become a 3mm stainless steel profile cut piece which bolts to the casting to “put back” the missing pivot tab .
0 2023/09/27 00:12:18
Second design at a pedal came out particularly nice , to be 12mm or 1/2” profile cut mild steel.
Second design at a pedal came out particularly nice , to be 12mm or 1/2” profile cut mild steel.
0 2023/09/27 00:12:31
The tilton 76 master isn’t a direct fit on the Center hole , I’d like to avoid machine work if possible so it’s a bit more of a bolt on kit .
The tilton 76 master isn’t a direct fit on the Center hole , I’d like to avoid machine work if possible so it’s a bit more of a bolt on kit .
0 2023/09/27 00:12:45
Tilton website has been very helpful to provide the necessary ratio and travel for the clutch pedal .
Tilton website has been very helpful to provide the necessary ratio and travel for the clutch pedal .
0 2023/09/27 00:12:55
0 2023/09/27 00:57:42
0 2023/09/30 23:18:42
0 2023/09/30 23:18:50
0 2023/10/03 15:04:32
0 2023/10/03 15:04:40
0 2023/10/03 15:04:46
0 2023/10/03 15:04:51
0 2023/10/03 15:04:56
0 2023/11/20 14:25:20
0 2024/04/19 03:19:10
0 2024/04/19 03:19:18