Jaguar Forums - Jaguar Enthusiasts Forum
Circled leak connection
Circled leak connection
0 2023/02/21 07:12:53
Evidence of leak at joint
Evidence of leak at joint
0 2023/02/21 07:12:58
Coolant Temp at 226F while causing in rain at outside temp of 50F
Coolant Temp at 226F while causing in rain at outside temp of 50F
0 2023/04/25 14:46:06
0 2023/04/25 14:47:52
0 2023/05/01 15:39:33
Judging from your diagram your numbering appears to be incorrect so you may have replaced the wrong injector. This photo is from the workshop manual.
Judging from your diagram your numbering appears to be incorrect so you may have replaced the wrong injector. This photo is from the workshop manual.
0 2023/05/15 13:51:33
This is the V6….There are 4 torx bolts each intercooler holding it to the cover. Probably a gasket too where the water feeds poke through the cover each side. However masking up as you planned should work.
This is the V6….There are 4 torx bolts each intercooler holding it to the cover. Probably a gasket too where the water feeds poke through the cover each side. However masking up as you planned should work.
0 2023/06/13 10:29:53
Loom as supplied
Loom as supplied
0 2023/10/04 11:18:13
unravel some of the loom tape to extend the overall length (reduce the 'Y" part)
unravel some of the loom tape to extend the overall length (reduce the 'Y" part)
0 2023/10/04 11:18:21
This is where the loom should come out inside the console
This is where the loom should come out inside the console
0 2023/10/04 11:22:56
My Dynamic setup has to be turned off, otherwise the screen is unresponsive
My Dynamic setup has to be turned off, otherwise the screen is unresponsive
0 2023/10/04 11:23:00
Automatic mic calibration
Automatic mic calibration
0 2023/10/04 11:23:06
Equalizer function
Equalizer function
0 2023/10/04 11:23:13
Volume settings
Volume settings
0 2023/10/04 11:23:19
0 2023/10/04 11:23:23
0 2023/10/04 11:23:29
0 2023/10/04 11:26:08
0 2023/10/04 11:28:29
0 2023/10/04 11:29:36
Concerns about operating temp of unit which gets hot! No other feasible location. This is operation without the trim panel back in place, so it's gonna get hotter once the panel is replaced..
Concerns about operating temp of unit which gets hot! No other feasible location. This is operation without the trim panel back in place, so it's gonna get hotter once the panel is replaced..
0 2023/10/04 13:11:58
Revised ( unwrapped at Y then rewrapped) loom to gain extra length needed
Revised ( unwrapped at Y then rewrapped) loom to gain extra length needed
0 2023/10/17 08:19:29
0 2023/10/17 08:19:40
0 2023/10/17 08:19:50
0 2024/01/29 05:10:52
0 2024/01/29 05:10:58
0 2024/01/29 05:11:03
0 2024/01/29 05:11:09
Interface Loom as supplier
Interface Loom as supplier
0 2024/01/29 05:11:16
Supplied loom unwound to gain extra length
Supplied loom unwound to gain extra length
0 2024/01/29 05:11:21
0 2024/01/29 05:11:26
0 2024/02/26 03:53:55
0 2024/02/26 03:54:36
0 2024/02/26 03:55:35
0 2024/06/24 12:31:52
0 2024/07/22 07:57:53
0 2024/07/22 07:58:29
location of existing Interface module (not ideal location for heat dissipation but required due to supplied loom connection points)
location of existing Interface module (not ideal location for heat dissipation but required due to supplied loom connection points)
0 2024/07/22 08:02:13
0 2025/08/11 06:42:51
0 2025/08/11 06:59:49
0 2025/08/11 07:02:02