Jaguar Forums - Jaguar Enthusiasts Forum
Passenger side spring pad and outer donut
Passenger side spring pad and outer donut
0 2021/05/22 13:57:15
Passenger side spring pad
Passenger side spring pad
0 2021/05/22 13:57:22
Passenger side spring pad
Passenger side spring pad
0 2021/05/22 13:57:28
Passenger side top
Passenger side top
0 2021/05/22 13:57:34
0 2021/05/22 13:57:39
Driver's side top
Driver's side top
0 2021/05/22 13:57:46
Left side; aka Driver's side.
Left side; aka Driver's side.
0 2021/06/27 17:32:45
Right side; aka passenger side
Right side; aka passenger side
0 2021/06/27 17:32:52
0 2021/07/09 10:28:14
0 2021/07/09 10:28:20
0 2021/07/09 10:28:27
0 2021/07/09 10:28:33
0 2021/07/24 03:54:53
Starting temp after the car has warmed up: 200°F
Starting temp after the car has warmed up: 200°F
0 2021/07/29 09:42:09
After a bit of driving in the city. Temp is about 213°F.
After a bit of driving in the city. Temp is about 213°F.
0 2021/07/29 09:42:16
I pulled onto a highway, steady 60 mph. Temperature dropped to about 207°F.
I pulled onto a highway, steady 60 mph. Temperature dropped to about 207°F.
0 2021/07/29 09:42:22
35° incline on the highway at 60 mph; temp is 215°F
35° incline on the highway at 60 mph; temp is 215°F
0 2021/07/29 09:42:28
At the incline passing another car at about ½ throttle input. Temp is about 217°F.
At the incline passing another car at about ½ throttle input. Temp is about 217°F.
0 2021/07/29 09:42:34
It started raining ambient temperature dropped from 94°F to 84°F, temperature is about 213°F
It started raining ambient temperature dropped from 94°F to 84°F, temperature is about 213°F
0 2021/07/29 09:42:40
Traffic slowed to 35 mph, temp rose again to 215°F
Traffic slowed to 35 mph, temp rose again to 215°F
0 2021/07/29 09:42:46
Traffic picked up again, accelerated to 60 mph. Temp was about 217°F
Traffic picked up again, accelerated to 60 mph. Temp was about 217°F
0 2021/07/29 09:42:52
At a stoplight for about a minute. Temperature rose to about 219°F.
At a stoplight for about a minute. Temperature rose to about 219°F.
0 2021/07/29 09:42:59
0 2021/07/29 09:43:05
A bit of hard driving, with revs reaching up to 5k rpm then stopped at a traffic light. Temperature hit about 222°F. When the car began moving again the temperature soon dropped to 215°F.
A bit of hard driving, with revs reaching up to 5k rpm then stopped at a traffic light. Temperature hit about 222°F. When the car began moving again the temperature soon dropped to 215°F.
0 2021/07/29 09:43:11
0 2021/07/29 09:43:17
0 2021/08/12 20:22:26
0 2021/08/12 20:22:33
As compared with the previous design, this allows the projector to sit about a ½ to ¾ inch further back than by using the center hole and the locking ring on the screw.
As compared with the previous design, this allows the projector to sit about a ½ to ¾ inch further back than by using the center hole and the locking ring on the screw.
0 2021/08/12 20:22:41
0 2021/08/12 20:22:48
0 2021/08/12 20:22:55
The hardest part was making sure that I was going to drill the holes in the correct area and keeping the projector centered on the reflector. An extra pair of hands are needed. The holes you drill on the reflector will be the same ones that the projector uses to secure the shroud. Then, fasten the screws through the reflector, the projector, and the shroud. It should look like in this picture.
The hardest part was making sure that I was going to drill the holes in the correct area and keeping the projector centered on the reflector. An extra pair of hands are needed. The holes you drill on the reflector will be the same ones that the projector uses to secure the shroud. Then, fasten the screws through the reflector, the projector, and the shroud. It should look like in this picture.
0 2021/08/12 20:23:02
The projector now sits nearly flush with the reflector.
The projector now sits nearly flush with the reflector.
0 2021/08/12 20:23:09
As I said before, it's not a perfect cut, but it does the job. The holes you drill are what needs to be perfect. As a bonus, the heat sink now has more room to breathe.
As I said before, it's not a perfect cut, but it does the job. The holes you drill are what needs to be perfect. As a bonus, the heat sink now has more room to breathe.
0 2021/08/12 20:23:19
I then overlayed the putty on the reflectors and used a thin Sharpie marker to trace the inside of it on the reflector. It doesn't have to come out perfect. After that was done, I used a Dremel to cut out these areas of the reflector, as you can see, it's not perfect, and it doesn't have to be.
I then overlayed the putty on the reflectors and used a thin Sharpie marker to trace the inside of it on the reflector. It doesn't have to come out perfect. After that was done, I used a Dremel to cut out these areas of the reflector, as you can see, it's not perfect, and it doesn't have to be.
0 2021/08/12 20:23:28
I got creative and used some Vinyl Polysiloxane putty (the stuff your dentist uses to take an impression of a crown or bridge preparation) to create an outline of back of the Morimoto Mini HB projector.
I got creative and used some Vinyl Polysiloxane putty (the stuff your dentist uses to take an impression of a crown or bridge preparation) to create an outline of back of the Morimoto Mini HB projector.
0 2021/08/12 20:23:39
0 2021/08/21 11:55:15
0 2021/08/21 11:55:25
0 2021/08/21 11:55:34
Here is an example of what you want to achieve.
Here is an example of what you want to achieve.
0 2021/08/31 12:18:05
0 2021/11/06 14:22:41