Jaguar Forums - Jaguar Enthusiasts Forum
end cap added to piece
end cap added to piece
0 2016/05/14 07:26:17
Another monocoque metalworks piece (upper quarter cP), needed to add a little touch to custom fit but as always a good panel
Another monocoque metalworks piece (upper quarter cP), needed to add a little touch to custom fit but as always a good panel
0 2016/05/14 07:26:13
Fitting the brace
Fitting the brace
0 2016/05/02 08:16:56
Trial fitting the bulkhead
Trial fitting the bulkhead
0 2016/05/02 08:16:51
Its in to stay now
Its in to stay now
0 2016/05/02 08:16:46
Its in to stay now
Its in to stay now
0 2016/05/02 08:16:42
0 2016/05/02 08:16:37
A few rust depressions I couldn't get out, but good integrity and ready to rebuild the rack
A few rust depressions I couldn't get out, but good integrity and ready to rebuild the rack
0 2016/05/02 08:16:32
Hmmm, smells good almost done!!
Hmmm, smells good almost done!!
0 2016/05/02 08:16:25
Side in last. Excellent fit with shifter cover. Will move to inner back bulkhead in the next few days now.
Side in last. Excellent fit with shifter cover. Will move to inner back bulkhead in the next few days now.
0 2016/04/27 06:19:48
Tunnel was tweeked and fitted 4-6 times before final welding
Tunnel was tweeked and fitted 4-6 times before final welding
0 2016/04/27 06:19:43
prepped for forward part of tunnel
prepped for forward part of tunnel
0 2016/04/27 06:19:35
Transmission tunnel welded ih. Lots of weld through primer and seam sealer used under it on seam in floor joint
Transmission tunnel welded ih. Lots of weld through primer and seam sealer used under it on seam in floor joint
0 2016/04/27 06:19:27
0 2016/04/23 18:04:04
Happy with fit for the most part but will need to change zome of the bends to better fit
Happy with fit for the most part but will need to change zome of the bends to better fit
0 2016/04/23 18:03:58
Rebuildong rear clip
Rebuildong rear clip
0 2016/04/23 18:03:52
Fitting right side of tunnel
Fitting right side of tunnel
0 2016/04/23 18:03:44
0 2016/04/13 17:48:10
Center brace welded in
Center brace welded in
0 2016/04/13 17:47:20
0 2016/04/08 10:46:39
should do it
should do it
0 2016/04/06 09:09:06
fitting panels- very fiddly, unlike today's cars and engineering, a lot of time spent fitting with dolly and hammer
fitting panels- very fiddly, unlike today's cars and engineering, a lot of time spent fitting with dolly and hammer
0 2016/04/06 09:08:49
fitting panels
fitting panels
0 2016/04/06 09:08:31
bare metal inside no wonder it rusted
bare metal inside no wonder it rusted
0 2016/04/06 09:07:58
0 2016/04/06 09:07:21
RUST!! who knew--ha ha
RUST!! who knew--ha ha
0 2016/04/06 09:07:03
0 2016/04/06 09:06:45
Fitting off side shut face patch panel
Fitting off side shut face patch panel
0 2016/04/06 09:06:02
red oxide primer
red oxide primer
0 2016/04/06 09:03:03
Box support for B post welded and seam sealer applied
Box support for B post welded and seam sealer applied
0 2016/04/06 09:02:37
Box support for B post welded and seam sealer applied
Box support for B post welded and seam sealer applied
0 2016/04/06 09:02:02
Fitting box support for B post. Patch panel for shut face welded in
Fitting box support for B post. Patch panel for shut face welded in
0 2016/04/06 09:01:35
Fitting box support for B post
Fitting box support for B post
0 2016/04/06 09:00:54
Fitting box support for B post
Fitting box support for B post
0 2016/04/06 09:00:29
0 2016/04/04 08:44:58
Trial fit of lower patch panel (Thanks Chuck at Monocoque metalworks!)
Trial fit of lower patch panel (Thanks Chuck at Monocoque metalworks!)
0 2016/04/04 08:44:51
Inner B post repair panel before final finish
Inner B post repair panel before final finish
0 2016/04/04 08:44:35
Fitting repair panel on b post
Fitting repair panel on b post
0 2016/04/03 21:47:48
M37 Dodge power wagon '52
M37 Dodge power wagon '52
0 2016/04/01 07:31:30
Lots of character: brits call this a Frogeye sprite vs. bugeye here in US
Lots of character: brits call this a Frogeye sprite vs. bugeye here in US
0 2016/04/01 07:26:26