Jaguar Forums - Jaguar Enthusiasts Forum
Fitting off side shut face patch panel
Fitting off side shut face patch panel
0 2016/04/06 09:06:02
0 2016/04/06 09:06:45
RUST!! who knew--ha ha
RUST!! who knew--ha ha
0 2016/04/06 09:07:03
0 2016/04/06 09:07:21
bare metal inside no wonder it rusted
bare metal inside no wonder it rusted
0 2016/04/06 09:07:58
fitting panels
fitting panels
0 2016/04/06 09:08:31
fitting panels- very fiddly, unlike today's cars and engineering, a lot of time spent fitting with dolly and hammer
fitting panels- very fiddly, unlike today's cars and engineering, a lot of time spent fitting with dolly and hammer
0 2016/04/06 09:08:49
should do it
should do it
0 2016/04/06 09:09:06
0 2016/04/08 10:46:39
Center brace welded in
Center brace welded in
0 2016/04/13 17:47:20
0 2016/04/13 17:48:10
Fitting right side of tunnel
Fitting right side of tunnel
0 2016/04/23 18:03:44
Rebuildong rear clip
Rebuildong rear clip
0 2016/04/23 18:03:52
Happy with fit for the most part but will need to change zome of the bends to better fit
Happy with fit for the most part but will need to change zome of the bends to better fit
0 2016/04/23 18:03:58
0 2016/04/23 18:04:04
Transmission tunnel welded ih. Lots of weld through primer and seam sealer used under it on seam in floor joint
Transmission tunnel welded ih. Lots of weld through primer and seam sealer used under it on seam in floor joint
0 2016/04/27 06:19:27
prepped for forward part of tunnel
prepped for forward part of tunnel
0 2016/04/27 06:19:35
Tunnel was tweeked and fitted 4-6 times before final welding
Tunnel was tweeked and fitted 4-6 times before final welding
0 2016/04/27 06:19:43
Side in last. Excellent fit with shifter cover. Will move to inner back bulkhead in the next few days now.
Side in last. Excellent fit with shifter cover. Will move to inner back bulkhead in the next few days now.
0 2016/04/27 06:19:48
Hmmm, smells good almost done!!
Hmmm, smells good almost done!!
0 2016/05/02 08:16:25
A few rust depressions I couldn't get out, but good integrity and ready to rebuild the rack
A few rust depressions I couldn't get out, but good integrity and ready to rebuild the rack
0 2016/05/02 08:16:32
0 2016/05/02 08:16:37
Its in to stay now
Its in to stay now
0 2016/05/02 08:16:42
Its in to stay now
Its in to stay now
0 2016/05/02 08:16:46
Trial fitting the bulkhead
Trial fitting the bulkhead
0 2016/05/02 08:16:51
Fitting the brace
Fitting the brace
0 2016/05/02 08:16:56
Another monocoque metalworks piece (upper quarter cP), needed to add a little touch to custom fit but as always a good panel
Another monocoque metalworks piece (upper quarter cP), needed to add a little touch to custom fit but as always a good panel
0 2016/05/14 07:26:13
end cap added to piece
end cap added to piece
0 2016/05/14 07:26:17
Mice profile/fit
Mice profile/fit
0 2016/05/14 07:26:21
Getting there
Getting there
0 2016/05/14 07:26:24
0 2016/05/14 07:26:28
NOS wing STILL needed some time on the english wheel to fit
NOS wing STILL needed some time on the english wheel to fit
0 2016/05/14 07:26:32
Edge curved into much, so wheeled it to bring out and will use planishing hammer and slap hammer to smooth more
Edge curved into much, so wheeled it to bring out and will use planishing hammer and slap hammer to smooth more
0 2016/05/14 07:26:35
fitting the new wing...it is a bear
fitting the new wing...it is a bear
0 2016/06/19 16:51:51
looks good but needs a lot of English wheel work for final fit
looks good but needs a lot of English wheel work for final fit
0 2016/06/19 16:52:05
looks good but needs a lot of English wheel work for final fit
looks good but needs a lot of English wheel work for final fit
0 2016/06/19 16:52:08
What have I done
What have I done
0 2016/06/19 16:52:10
preliminary boot and rear bulk head fitting
preliminary boot and rear bulk head fitting
0 2016/06/19 16:52:13
quarter panel caps from Chuck
quarter panel caps from Chuck
0 2016/06/19 16:52:16
Getting ready to weld in
Getting ready to weld in
0 2016/06/19 16:52:25