Jaguar Forums - Jaguar Enthusiasts Forum
0 2018/05/13 16:38:33
0 2018/05/15 15:32:51
0 2018/05/15 15:33:18
0 2018/05/21 16:05:55
To get the Brake Pump open, I had to drill through these Anti Tamper rings
To get the Brake Pump open, I had to drill through these Anti Tamper rings
0 2018/05/21 16:06:34
I had to pull the top off to get to the Commutator where I found that the Bearings were shot and the Commutator was burned black
I had to pull the top off to get to the Commutator where I found that the Bearings were shot and the Commutator was burned black
0 2018/05/21 16:12:01
The Commutator was Burned black and the Bearings were shot
The Commutator was Burned black and the Bearings were shot
0 2018/05/21 16:15:37
Graunch marks on the Commutator where the Bearings had seized up
Graunch marks on the Commutator where the Bearings had seized up
0 2018/05/21 16:17:10
The Brushes and Brush Holders had completely melted!
The Brushes and Brush Holders had completely melted!
0 2018/05/21 16:22:35
I pulled the bottom cap off to see what was underneath
I pulled the bottom cap off to see what was underneath
0 2018/05/21 16:24:41
The only good bit left! but underneath this bearing holder which was also locked the Brushes and Brush Holders had completely melted
The only good bit left! but underneath this bearing holder which was also locked the Brushes and Brush Holders had completely melted
0 2018/05/21 16:26:28
This is where the Brake Pump Motor bolts onto the Brake Pump
This is where the Brake Pump Motor bolts onto the Brake Pump
0 2018/05/21 16:33:41
With the Brake Pump Motor Burned out the only thing worth saving could be the Pressure Switch and the 'Black Ball' (Accumulator)
With the Brake Pump Motor Burned out the only thing worth saving could be the Pressure Switch and the 'Black Ball' (Accumulator)
0 2018/05/21 16:37:51
Drilling a hole in the side of a Nut to go over the 'rounded' Bleed Nipple
Drilling a hole in the side of a Nut to go over the 'rounded' Bleed Nipple
0 2018/05/22 15:42:03
The idea was to slip the Nut over the 'rounded' Bleed Nipple and then once having done so Mig Weld it through the hole that I had drilled
The idea was to slip the Nut over the 'rounded' Bleed Nipple and then once having done so Mig Weld it through the hole that I had drilled
0 2018/05/22 15:43:23
Just what I've always wanted a Mig Welder!
Just what I've always wanted a Mig Welder!
0 2018/05/22 15:51:02
MUREX 130 Mig Welder, with all the 'bells and whistles'
MUREX 130 Mig Welder, with all the 'bells and whistles'
0 2018/05/22 15:52:07
Forked Shield for Spot Welding
Forked Shield for Spot Welding
0 2018/05/22 15:56:27
Practice Spot Welds on the Left but the one on the Right was the one I wanted and even a Spot Weld much smaller than that would have been enough to do the Job
Practice Spot Welds on the Left but the one on the Right was the one I wanted and even a Spot Weld much smaller than that would have been enough to do the Job
0 2018/05/22 15:59:05
Auto Darkening Welding Mask, how did I ever manage without one of these
Auto Darkening Welding Mask, how did I ever manage without one of these
0 2018/05/22 16:03:36
All the Tools to do the Job and I used the Grinder to make sure I got a good earth and also cleaned up the Bleed Nipple with a Wire Brush
All the Tools to do the Job and I used the Grinder to make sure I got a good earth and also cleaned up the Bleed Nipple with a Wire Brush
0 2018/05/22 16:05:13
Removing the Rear Silencer was 'The Job From Hell'
Removing the Rear Silencer was 'The Job From Hell'
0 2018/05/22 16:14:51
The 'Rounded off' Brake Bleed Nipple
The 'Rounded off' Brake Bleed Nipple
0 2018/05/22 23:33:01
Drilled Nut with the Hole in placed over the Brake Bleed Nipple already for 'Spot Welding'
Drilled Nut with the Hole in placed over the Brake Bleed Nipple already for 'Spot Welding'
0 2018/05/22 23:34:26
Assorted Shrink Wrap Tubing
Assorted Shrink Wrap Tubing
0 2018/05/24 14:02:08
Lots of different sizes to fit almost any Wire
Lots of different sizes to fit almost any Wire
0 2018/05/24 14:03:02
Slide the Tube over the Wire
Slide the Tube over the Wire
0 2018/05/24 14:05:15
Carefully Heat the Shrink Wrap Tube
Carefully Heat the Shrink Wrap Tube
0 2018/05/24 14:06:12
The Shrink Wrap Tube holds really tight and almost any source of Heat will do but keep it away from anything inflamable
The Shrink Wrap Tube holds really tight and almost any source of Heat will do but keep it away from anything inflamable
0 2018/05/24 14:07:22
As you may see I was able to get a good hit on the side of the Bleed Nipple with a Chisel but it wouldn't budge and eventually Broke Off
As you may see I was able to get a good hit on the side of the Bleed Nipple with a Chisel but it wouldn't budge and eventually Broke Off
0 2018/05/24 14:48:32
What's left of the Broken Bleed Nipple
What's left of the Broken Bleed Nipple
0 2018/05/24 14:53:11
NGK BR7EF Spark Plugs
NGK BR7EF Spark Plugs
0 2018/05/26 07:11:05
Is that the round cover you mean Jay?
Is that the round cover you mean Jay?
0 2018/05/30 15:28:11
Dry as a bone with not a drop Power Steering Fluid in sight
Dry as a bone with not a drop Power Steering Fluid in sight
0 2018/06/02 16:57:58
ATF-U Fully Synthetic Power Steering Fluid cured my Power Steering Leak!
ATF-U Fully Synthetic Power Steering Fluid cured my Power Steering Leak!
0 2018/06/02 17:00:09
After numerous Trips the Fully Synthetic Power Steering Fluid was right up to the mark, so well done to 'The Wizard' for that Awesome Tip!
After numerous Trips the Fully Synthetic Power Steering Fluid was right up to the mark, so well done to 'The Wizard' for that Awesome Tip!
0 2018/06/02 17:02:35
Sticky Petrol Substance on the Fuel Rail
Sticky Petrol Substance on the Fuel Rail
0 2018/06/03 11:04:58
Petrol Leaking out of the Injector Stem
Petrol Leaking out of the Injector Stem
0 2018/06/03 11:06:34
Although I've cleaned the Injector Stem with White Spirit, I haven't attempted to tighten anything up yet
Although I've cleaned the Injector Stem with White Spirit, I haven't attempted to tighten anything up yet
0 2018/06/03 11:08:07
Leaking Fuel around that Injector Seal was almost certainly 'Cooking' and causing that 'Sweet Sickly Smell' that I had been smelling all day
Leaking Fuel around that Injector Seal was almost certainly 'Cooking' and causing that 'Sweet Sickly Smell' that I had been smelling all day
0 2018/06/04 01:30:44