Jaguar Forums - Jaguar Enthusiasts Forum
both compressors showing parts
both compressors showing parts
0 2016/07/04 10:36:28
fuzzy pic but dowel is ~5/8" down from end (3/4" was too far)
fuzzy pic but dowel is ~5/8" down from end (3/4" was too far)
0 2016/07/04 10:36:32
2 different size washers used, big ones go against spring seat in car
2 different size washers used, big ones go against spring seat in car
0 2016/07/04 10:36:36
1 set of self aligning washers. Curved faces for each set face each other. Flat faces of each pair face out
1 set of self aligning washers. Curved faces for each set face each other. Flat faces of each pair face out
0 2016/07/04 10:36:40
I filed a flat so I could center punch for the drilled hole. I drilled 1/64" under, then 1/4" finished size and had a nice tight slip fit.
I filed a flat so I could center punch for the drilled hole. I drilled 1/64" under, then 1/4" finished size and had a nice tight slip fit.
0 2016/07/04 10:36:43
both compressors side by side, one assembled, 2nd showing the order of assy
both compressors side by side, one assembled, 2nd showing the order of assy
0 2016/07/04 16:41:35
fuzzy picture but shows the dowel center line ~ 5/8" below end of threaded rod (3/4" wouldn't fit)
fuzzy picture but shows the dowel center line ~ 5/8" below end of threaded rod (3/4" wouldn't fit)
0 2016/07/04 16:41:41
2 different size washers, big ones go against the bottom of the spring pan
2 different size washers, big ones go against the bottom of the spring pan
0 2016/07/04 16:41:47
1 pair of self aligning washers, spherical faces face each other, 2 pairs back to back, flat faces face out on each pair
1 pair of self aligning washers, spherical faces face each other, 2 pairs back to back, flat faces face out on each pair
0 2016/07/04 16:41:53
I filed a flat on the end of the threaded rod so I could center punch for the cross hole. I drilled thru with a 15/64" bit 1st then 1/4" and it gave me a nice tight slip fit for the dowel
I filed a flat on the end of the threaded rod so I could center punch for the cross hole. I drilled thru with a 15/64" bit 1st then 1/4" and it gave me a nice tight slip fit for the dowel
0 2016/07/04 16:41:57
both compressors side by side, showing order of assy
both compressors side by side, showing order of assy
0 2016/07/04 16:55:11
fuzzy picture showing dowel centerline ~5/8" below end of rod (3/4" didn't fit)
fuzzy picture showing dowel centerline ~5/8" below end of rod (3/4" didn't fit)
0 2016/07/04 16:55:13
2 different size washers, big ones go against the bottom of the spring pan
2 different size washers, big ones go against the bottom of the spring pan
0 2016/07/04 16:55:14
1 pair of self aligning washers, spherical faces go against each other, flat faces face out, 2 pairs back to back on each compressor
1 pair of self aligning washers, spherical faces go against each other, flat faces face out, 2 pairs back to back on each compressor
0 2016/07/04 16:55:15
I filed a flat on the end of the rod so I could center punch for the cross hole. I drilled a 15/64" hole 1st then a 1/4" hole and had a nice tight slip fit.
I filed a flat on the end of the rod so I could center punch for the cross hole. I drilled a 15/64" hole 1st then a 1/4" hole and had a nice tight slip fit.
0 2016/07/04 16:55:16
0 2025/05/08 08:42:22