Jaguar Forums - Jaguar Enthusiasts Forum
1997 X300 airbox inlet horn
1997 X300 airbox inlet horn
0 2016/10/21 11:16:46
0 2016/10/23 20:38:40
Plastic slider support block behind the wrap around edge of the front bumper on a 1997 XJ6
Plastic slider support block behind the wrap around edge of the front bumper on a 1997 XJ6
0 2016/10/23 20:39:58
Normal bumper to fender gap on other side of the car.
Normal bumper to fender gap on other side of the car.
0 2016/10/23 20:41:17
Mystery plastic panel wandering around loose under the bonnet on left hand side of the engine compartment.
Mystery plastic panel wandering around loose under the bonnet on left hand side of the engine compartment.
0 2016/10/24 21:45:17
Weird battery cable end with no way to clamp to post
Weird battery cable end with no way to clamp to post
0 2016/10/24 21:48:09
0 2016/11/09 20:32:16
0 2016/11/09 20:32:27
Cam cover removed from the engine
Cam cover removed from the engine
0 2018/12/22 06:40:07
Trunk ful of removed parts
Trunk ful of removed parts
0 2018/12/22 06:41:10
Cam cover removed
Cam cover removed
0 2018/12/22 06:42:43
Removed parts in the trunk
Removed parts in the trunk
0 2018/12/22 06:43:41
0 2018/12/22 06:46:52
Removed parts in trunk
Removed parts in trunk
0 2018/12/22 06:47:12
Lots of patches held on with braze
Lots of patches held on with braze
0 2019/01/02 14:27:32
Lots of patches help on with braze
Lots of patches help on with braze
0 2019/01/02 14:30:21
Front grill removed to show disassembled engine
Front grill removed to show disassembled engine
0 2019/01/12 07:41:28
Front of motor after removal of the water pump
Front of motor after removal of the water pump
0 2019/01/25 23:44:43
After removing the lower timing cover
After removing the lower timing cover
0 2019/01/25 23:46:18
HUGE crack
HUGE crack
0 2019/03/18 19:51:53
brown discoloration on block around cylinder number three
brown discoloration on block around cylinder number three
0 2019/04/24 16:50:33
Similar discoloration on bottom of head gasket around cylinder three sealing surface.
Similar discoloration on bottom of head gasket around cylinder three sealing surface.
0 2019/04/24 16:51:26
brown discoloration on block around cylinder number three
brown discoloration on block around cylinder number three
0 2019/04/24 16:55:38
Similar discoloration on bottom of head gasket around cylinder three sealing surface.
Similar discoloration on bottom of head gasket around cylinder three sealing surface.
0 2019/04/24 16:56:03
Destroyed intake manifold
Destroyed intake manifold
0 2019/05/01 19:10:46
Disassembling FLAT head
Disassembling FLAT head
0 2019/05/04 07:22:22
See machined slot at lower edge of the ridge around the hole.
See machined slot at lower edge of the ridge around the hole.
0 2019/05/06 21:10:02
Closeup of the same edge showing the machined slot.
Closeup of the same edge showing the machined slot.
0 2019/05/06 21:10:58
same hole edge on the 1997 car with no slot
same hole edge on the 1997 car with no slot
0 2019/05/06 21:12:39
See ridge that is in the transition from the valve seat down into the port?
See ridge that is in the transition from the valve seat down into the port?
0 2019/05/14 16:22:44
0 2019/05/14 16:27:31
Intake ports on the bottom of the photo
Intake ports on the bottom of the photo
0 2019/05/14 16:28:18
0 2019/05/14 16:30:02
Ford exhaust ports
Ford exhaust ports
0 2019/05/14 16:31:48
AJ6 cast iron exhaust manifold
AJ6 cast iron exhaust manifold
0 2019/05/14 16:37:46
Exhaust port with gasket in place
Exhaust port with gasket in place
0 2019/05/14 16:51:03
Heater control valve as installed on the engine
Heater control valve as installed on the engine
0 2019/05/15 13:35:10
Corroded heater control valve showing nut & olive that screws and seals in fitting on the cylinder head
Corroded heater control valve showing nut & olive that screws and seals in fitting on the cylinder head
0 2019/05/15 13:36:01
Fitting located in the rear left hand corner of the cylinder head The nut on the heater control vale screws into the nut in the cylinder head and seals with the olive or ferrule.
Fitting located in the rear left hand corner of the cylinder head The nut on the heater control vale screws into the nut in the cylinder head and seals with the olive or ferrule.
0 2019/05/15 13:36:56
Pre-1993 heater control valve
Pre-1993 heater control valve
0 2019/05/15 13:43:30