Jaguar Forums - Jaguar Enthusiasts Forum
0 2020/01/25 08:05:42
0 2020/01/25 08:04:41
0 2018/11/19 23:43:42
0 2018/11/19 23:38:05
0 2018/11/19 23:37:19
0 2018/11/19 23:34:47
0 2018/11/19 23:33:48
0 2018/11/19 23:30:41
0 2018/11/19 23:29:36
0 2018/11/19 23:26:13
0 2018/11/19 23:24:46
0 2018/11/19 23:23:01
0 2018/11/19 23:17:32
SS pipe in valley
SS pipe in valley
0 2017/07/16 23:18:16
new fitting for brake vacuum line
new fitting for brake vacuum line
0 2017/07/16 22:59:44
Fit of bolt with rubber and O-ring.
Fit of bolt with rubber and O-ring.
0 2017/07/11 08:46:12
O-ring added on top of rubber
O-ring added on top of rubber
0 2017/07/11 08:45:21
Bolt with standard rubber
Bolt with standard rubber
0 2017/07/11 08:44:23
Before adding an O-ring
Before adding an O-ring
0 2017/07/11 08:41:57
Vacuum pipe and hole. What is missing?
Vacuum pipe and hole. What is missing?
0 2017/07/11 00:01:11
Black hole. Sucks everything from everywhere!
Black hole. Sucks everything from everywhere!
0 2017/07/10 23:36:37
The beginning bulge can be noticed to the right of the pipe in the valley. It could be mistaken for Chris Christie!
The beginning bulge can be noticed to the right of the pipe in the valley. It could be mistaken for Chris Christie!
0 2017/07/04 10:35:41
Taking pictures around corners!! shows this neat, and very tight connection. Tomorrow the hunt is on for a bigger torque wrench to just make damned sure this baby is vas! (fas=tight) in Afrikaans!
Taking pictures around corners!! shows this neat, and very tight connection. Tomorrow the hunt is on for a bigger torque wrench to just make damned sure this baby is vas! (fas=tight) in Afrikaans!
0 2017/06/28 09:50:43
380Nm of torque!!! Pulley arrester that actually works! My torque wrench goes to 200Nm. The rest done with a breaker bar and a healthy extension! AArrrrgh!
380Nm of torque!!! Pulley arrester that actually works! My torque wrench goes to 200Nm. The rest done with a breaker bar and a healthy extension! AArrrrgh!
0 2017/06/28 09:48:48
After cutting a split with an angle grinder, voila!! new fatter, shining and slightly longer split collet!
After cutting a split with an angle grinder, voila!! new fatter, shining and slightly longer split collet!
0 2017/06/28 09:46:24
After parting off the stock, still hot and good looking!
After parting off the stock, still hot and good looking!
0 2017/06/28 09:45:19
After the pulley, now the new collet. Keeping the same setting on the lathe, and hand feeding, I will get the same taper on collet and pulley, given some grace!
After the pulley, now the new collet. Keeping the same setting on the lathe, and hand feeding, I will get the same taper on collet and pulley, given some grace!
0 2017/06/28 09:42:49
After clean up.
After clean up.
0 2017/06/28 09:41:58
The worn taper on the pulley. It has a 10 degree angle, so I set the cross slide to 10 degrees and claeaned the surface. My boring bar was almost too short, and I had a bit of chatter on the feed in. I had to grip the pulley on the oil seal surface at the back as the pulley is not centered if you grip the outside. That made the distance from the tool holder longer and allowed for the vibration. Nothing to be done about that except buying a sturdier longer boring bar, so I live with this.
The worn taper on the pulley. It has a 10 degree angle, so I set the cross slide to 10 degrees and claeaned the surface. My boring bar was almost too short, and I had a bit of chatter on the feed in. I had to grip the pulley on the oil seal surface at the back as the pulley is not centered if you grip the outside. That made the distance from the tool holder longer and allowed for the vibration. Nothing to be done about that except buying a sturdier longer boring bar, so I live with this.
0 2017/06/28 09:37:43
0 2017/06/28 09:26:05
Machining the outside of the split collet from a hollow bar
Machining the outside of the split collet from a hollow bar
0 2017/06/28 09:16:56
0 2017/06/28 09:09:00
SS pipe. Still need to machine two end fittings to take the rubber pipes.
SS pipe. Still need to machine two end fittings to take the rubber pipes.
0 2017/06/26 08:15:15
Supercharger out, revealing a mouse nest under the charger, and a cooling pipe in the first stage of failure
Supercharger out, revealing a mouse nest under the charger, and a cooling pipe in the first stage of failure
0 2017/06/25 12:12:49
0 2017/06/25 12:12:14
0 2017/06/25 04:26:32
Nulon does not look healthy!
Nulon does not look healthy!
0 2017/06/21 13:46:29
Pulley gone AWOL
Pulley gone AWOL
0 2017/06/21 13:21:29
My fearless cat came to great the Jaguar! She liked it!!
My fearless cat came to great the Jaguar! She liked it!!
0 2017/06/21 13:19:52
At the start of the journey to the center of the universe!
At the start of the journey to the center of the universe!
0 2017/06/21 13:17:58