Jaguar Forums - Jaguar Enthusiasts Forum
0 2025/06/07 16:15:47
0 2025/06/06 12:02:27
0 2025/05/27 16:41:56
0 2025/05/26 16:15:43
0 2025/05/26 16:13:41
0 2024/05/31 11:39:24
0 2024/05/31 11:39:14
0 2024/05/30 23:32:38
Glad I did. The flush mount looks wayyy better. Need to touch up the nick made from drilling 🤦🏾‍♂️
Glad I did. The flush mount looks wayyy better. Need to touch up the nick made from drilling 🤦🏾‍♂️
0 2024/05/30 23:32:30
1st camera was good.. but was a cubic shape. Would be difficult to cut a square hole. I remembered I ordered a brand new Natika AHD camera a while back..and used it instead. The housing needed to be trimmed some. This camera had a metal housing, which made it a PITA.
1st camera was good.. but was a cubic shape. Would be difficult to cut a square hole. I remembered I ordered a brand new Natika AHD camera a while back..and used it instead. The housing needed to be trimmed some. This camera had a metal housing, which made it a PITA.
0 2024/05/30 23:32:24
This part was nerve wracking. I had the drill torque set too high. The bit snagged, cause a kickback..and scratched it a bit. It could've been worse.
This part was nerve wracking. I had the drill torque set too high. The bit snagged, cause a kickback..and scratched it a bit. It could've been worse.
0 2024/05/30 23:32:09
Marking the center. Used a small tap on the inside as a guide.
Marking the center. Used a small tap on the inside as a guide.
0 2024/05/30 23:31:50
The 1st camera was nice..but had a cubic shape. Would be too difficult trying to make a square hole. Forgot I had a new Nakang
The 1st camera was nice..but had a cubic shape. Would be too difficult trying to make a square hole. Forgot I had a new Nakang
0 2024/05/30 23:23:02
Used the center tab as a guide.
Used the center tab as a guide.
0 2024/05/30 23:20:48
0 2024/05/29 22:43:03
I didn't want to fully rid of this aluminum part. I lined the camera to trace around it..then used snips to cut it out. I made remove the case of the camera also. Its sealed inside and has half and inch of hollow space. Plus it will not be exposed to the weather.
I didn't want to fully rid of this aluminum part. I lined the camera to trace around it..then used snips to cut it out. I made remove the case of the camera also. Its sealed inside and has half and inch of hollow space. Plus it will not be exposed to the weather.
0 2024/05/29 22:40:09
Under side.
Under side.
0 2024/05/29 22:36:07
Next was to use a step drill to go thru the circuit board
Next was to use a step drill to go thru the circuit board
0 2024/05/29 22:35:49
0 2024/05/29 22:32:20
0 2024/05/29 17:15:29
0 2023/12/08 18:04:50
Used a Dremel cut a slit for the wires
Used a Dremel cut a slit for the wires
0 2023/12/08 18:04:34
Like so
Like so
0 2023/12/08 18:04:24
Look closely this is what you slide the tabs under..the clip the bottom.
Look closely this is what you slide the tabs under..the clip the bottom.
0 2023/12/08 18:04:12
This part clip on the cross section that you use to pull the vents out
This part clip on the cross section that you use to pull the vents out
0 2023/12/08 18:03:59
This part is what will be swapped to the non-illuminated vents. It has 2 tiny tabs that needs to slide under 2 notches on the other (see next pic)
This part is what will be swapped to the non-illuminated vents. It has 2 tiny tabs that needs to slide under 2 notches on the other (see next pic)
0 2023/12/08 18:03:51
This pick came in handy removing the clips.
This pick came in handy removing the clips.
0 2023/12/08 18:03:42
My 2 rear vents out
My 2 rear vents out
0 2023/12/08 18:02:04
0 2023/12/06 03:22:15
0 2023/12/06 03:21:51
I also noticed some of these plastic ones have only 2 mounting screws, while the aluminum has 3 holes. Can anyone give some insight on this? How do I know which one I need? Car is a 2016 XJL
I also noticed some of these plastic ones have only 2 mounting screws, while the aluminum has 3 holes. Can anyone give some insight on this? How do I know which one I need? Car is a 2016 XJL
0 2023/10/20 08:52:39
I purchased this aluminum part. Has anyone installed one from this company?
I purchased this aluminum part. Has anyone installed one from this company?
0 2023/10/20 08:52:37
0 2023/10/16 12:19:32
0 2023/10/16 10:20:41
Used a loaner serpentine tool to pry it up... made this part a breeze. This helped out tremendously. Its soft and doesn't damage anything.
Used a loaner serpentine tool to pry it up... made this part a breeze. This helped out tremendously. Its soft and doesn't damage anything.
0 2023/10/16 10:20:25
Leak was worse than I thought
Leak was worse than I thought
0 2023/10/16 10:18:42
Took me way longer than I wanted.. but got it done 😤
Took me way longer than I wanted.. but got it done 😤
0 2023/10/16 10:17:41
0 2023/10/14 21:35:01
0 2023/10/05 13:49:14
0 2023/10/01 10:35:26