Jaguar Forums - Jaguar Enthusiasts Forum
Looks like a galley of some kind?
Looks like a galley of some kind?
0 2024/03/19 21:25:23
Plug is at the top of the crankshaft with the female Allen.
Plug is at the top of the crankshaft with the female Allen.
0 2024/03/19 21:25:17
Anyone know what this is?
Anyone know what this is?
0 2023/04/03 21:14:11
0 2021/06/16 06:46:21
0 2020/04/20 19:33:44
0 2020/04/20 19:33:00
Here is the leak. I cleaned the engine Prior to start but the leak is pretty bad.
Here is the leak. I cleaned the engine Prior to start but the leak is pretty bad.
0 2020/04/20 19:28:12
Pull the tank. The D clips for the lines just rotate Don't remove! I replaced them because when I removed them they were to bent to work well.
Pull the tank. The D clips for the lines just rotate Don't remove! I replaced them because when I removed them they were to bent to work well.
0 2019/09/25 09:07:42
0 2019/09/24 21:12:57
The fuel check valve came from a local speed shop. I didn't remember the size of the fuel lines. so I got two types of barb fittings. They are 5/16 FYI. The D clips and the fuel line O-rings came from Jagbits
The fuel check valve came from a local speed shop. I didn't remember the size of the fuel lines. so I got two types of barb fittings. They are 5/16 FYI. The D clips and the fuel line O-rings came from Jagbits
0 2019/09/24 21:06:39
1 2019/09/24 21:06:31
Replace o-rings one line
Replace o-rings one line
0 2019/09/24 19:29:53
Reinstall the module in tank. Make sure the fuel sender has room to travel. I had to bend mine out of the way slightly.
Reinstall the module in tank. Make sure the fuel sender has room to travel. I had to bend mine out of the way slightly.
1 2019/09/24 19:29:49
The diagram in the manual is not correct. the pressure side is the brass fitting
The diagram in the manual is not correct. the pressure side is the brass fitting
0 2019/09/24 19:29:46
This is the old pressure line. I tried to keep the same angle with the added length of the check valve.
This is the old pressure line. I tried to keep the same angle with the added length of the check valve.
1 2019/09/24 19:29:42
Pull the module
Pull the module
0 2019/09/24 19:29:37
0 2019/09/24 19:29:33
1 2019/09/24 19:29:29
These clips are not intuitive until you see them out. just rotate 90deg and pull. DO NOT REMOVE, or you will probably develop a leak at some point.
These clips are not intuitive until you see them out. just rotate 90deg and pull. DO NOT REMOVE, or you will probably develop a leak at some point.
0 2019/09/24 19:29:25
Got it in and mostly hooked up. Few more hours more to go.
Got it in and mostly hooked up. Few more hours more to go.
0 2019/09/22 20:48:11
Had to use a jack on the tranny and remove the steering rack.
Had to use a jack on the tranny and remove the steering rack.
0 2019/09/22 20:47:07
0 2019/09/22 20:47:00
Angle gets pretty crazy going in. Didn’t like all the weight on the chain that came with the leveler. Borrowed a beefier one to put it in
Angle gets pretty crazy going in. Didn’t like all the weight on the chain that came with the leveler. Borrowed a beefier one to put it in
0 2019/09/22 20:46:54
0 2019/09/20 07:06:24
0 2019/09/20 07:05:57
0 2019/09/19 13:34:35
0 2019/05/03 06:06:09