Jaguar Forums - Jaguar Enthusiasts Forum
0 2023/07/10 04:17:56
0 2023/07/10 04:17:55
0 2023/07/10 04:17:53
0 2023/07/10 04:17:52
Then some shrink wrap and electrical tape to finish the job, and the top was working again!
Then some shrink wrap and electrical tape to finish the job, and the top was working again!
0 2022/10/01 04:29:45
We stitched the conductors back together and soldered the bundle.
We stitched the conductors back together and soldered the bundle.
0 2022/10/01 04:28:54
Once we were in there, the broken wire was easy to spot!
Once we were in there, the broken wire was easy to spot!
0 2022/10/01 04:27:41
You will have to cut and pull back the nylon our cover to inspect the wires…
You will have to cut and pull back the nylon our cover to inspect the wires…
0 2022/10/01 04:26:30
This is the trouble spot on the driver’s side.
This is the trouble spot on the driver’s side.
0 2022/10/01 04:25:29
0 2022/04/25 06:53:54
Happy iPhone SE displaying Google maps.
Happy iPhone SE displaying Google maps.
0 2022/01/21 12:48:55
Charge plate version installed in place of factory ashtray.
Charge plate version installed in place of factory ashtray.
0 2022/01/21 12:48:50
Latest generation charge plate version.
Latest generation charge plate version.
0 2022/01/21 12:48:44
The vent-substitute version in white and two generations of the integrated charge plate version.
The vent-substitute version in white and two generations of the integrated charge plate version.
0 2022/01/21 12:48:39
Ashtray with Qi charger
Ashtray with Qi charger
0 2021/12/12 15:08:54
Ashtray with dividers
Ashtray with dividers
0 2021/12/12 15:08:51
The access port in the trunk, RH side.
The access port in the trunk, RH side.
0 2021/12/02 10:34:44
The USB interface hiding in back.
The USB interface hiding in back.
0 2021/12/02 10:34:39
0 2021/11/29 16:09:09
Replacement IBOC module from 2010 XK.
Replacement IBOC module from 2010 XK.
0 2017/05/10 05:31:58
IBOC module from 2010 XKR with bad AM function
IBOC module from 2010 XKR with bad AM function
0 2017/05/10 05:31:56
24. Put the mounting plate on your new tuner and reverse the process to install it!
24. Put the mounting plate on your new tuner and reverse the process to install it!
0 2017/05/04 17:32:47
23. The stack comes off straight up when the four nuts are removed, and the IBOC tuner then can be removed with its mounting plate which sits on the four mounting studs you removed the nuts from. You will need a T25 driver to unscrew the IBOC tuner housing from the mounting plate.
23. The stack comes off straight up when the four nuts are removed, and the IBOC tuner then can be removed with its mounting plate which sits on the four mounting studs you removed the nuts from. You will need a T25 driver to unscrew the IBOC tuner housing from the mounting plate.
0 2017/05/04 17:32:36
21. Carefully slide the driver onto the front nut and unwind it.
21. Carefully slide the driver onto the front nut and unwind it.
0 2017/05/04 17:32:21
22. Then remove the nut closest to the battery terminal. BE CAREFUL.
22. Then remove the nut closest to the battery terminal. BE CAREFUL.
0 2017/05/04 17:32:13
20. On the battery side of the stack, BE VERY CAREFUL. You will be working right next to the positive battery terminal. DON'T TOUCH IT WITH YOUR DRIVER!
20. On the battery side of the stack, BE VERY CAREFUL. You will be working right next to the positive battery terminal. DON'T TOUCH IT WITH YOUR DRIVER!
0 2017/05/04 17:32:05
17. Now you can put your socket and driver onto the rear nut of the mounting bracket.
17. Now you can put your socket and driver onto the rear nut of the mounting bracket.
0 2017/05/04 17:31:57
18. And onto the front nut of the mounting bracket.
18. And onto the front nut of the mounting bracket.
0 2017/05/04 17:31:48
16. Pull this connector from the right hand side of the component stack, to give room to work on the mounting screws.
16. Pull this connector from the right hand side of the component stack, to give room to work on the mounting screws.
0 2017/05/04 17:31:35
19. You will want to remove this harness section from the holder to get access to the frontward RHS mounting nut.
19. You will want to remove this harness section from the holder to get access to the frontward RHS mounting nut.
0 2017/05/04 17:31:26
14. You need to close the top only until the point that both the tonneau cover and rear window are wide open, then stop there. The top will hold this position but only for a little while, so the next steps need to be done quickly.
14. You need to close the top only until the point that both the tonneau cover and rear window are wide open, then stop there. The top will hold this position but only for a little while, so the next steps need to be done quickly.
0 2017/05/04 17:31:17
12. Now you need to put the windowshade cover back in place so you can partially close the top and access the mounting screws from the top.
12. Now you need to put the windowshade cover back in place so you can partially close the top and access the mounting screws from the top.
0 2017/05/04 17:31:06
13. Both sides need to be snapped down, and then the windowshade closed or the top will not fold.
13. Both sides need to be snapped down, and then the windowshade closed or the top will not fold.
0 2017/05/04 17:30:58
11. This connector has a snap on the side and can be removed more easily.
11. This connector has a snap on the side and can be removed more easily.
0 2017/05/04 17:30:48
10. There are two connections to the IBOC tuner module to be removed. The RF connector is by far the harder connector to remove. It has a tab on the bottom side that has to be pushed into the connector to release it from the far side. I released it after removing the stack because I could not get my finger under the connector to access the tabl.
10. There are two connections to the IBOC tuner module to be removed. The RF connector is by far the harder connector to remove. It has a tab on the bottom side that has to be pushed into the connector to release it from the far side. I released it after removing the stack because I could not get my finger under the connector to access the tabl.
0 2017/05/04 17:30:39
15. You will need a 10 mm socket and screwdriver handle or socket extension and socket wrench to remove the four mounting screws.
15. You will need a 10 mm socket and screwdriver handle or socket extension and socket wrench to remove the four mounting screws.
0 2017/05/04 17:30:27
9. There is a tab on the top of this connector (tilted toward the camera in this shot); the tab must be pulled away from the connector body to release the connector from the metal tab it hooks onto.
9. There is a tab on the top of this connector (tilted toward the camera in this shot); the tab must be pulled away from the connector body to release the connector from the metal tab it hooks onto.
0 2017/05/04 17:30:19
8. You will also want to remove this cable for access to the screws.
8. You will also want to remove this cable for access to the screws.
0 2017/05/04 17:30:12
7. You will need to remove this cable hanger from the outside of the rack to be able to access the mounting screws. This is more easily done through the trunk, IMHO.
7. You will need to remove this cable hanger from the outside of the rack to be able to access the mounting screws. This is more easily done through the trunk, IMHO.
0 2017/05/04 17:30:03
6. Here is the stack with the DVD for the Navigation system and, on the bottom, the IBOC tuner.
6. Here is the stack with the DVD for the Navigation system and, on the bottom, the IBOC tuner.
0 2017/05/04 17:29:55