Jaguar Forums - Jaguar Enthusiasts Forum
0 2018/07/16 18:30:12
One each side looks similar. Pulling out slightly so you can get a finger under the bottom edge.
One each side looks similar. Pulling out slightly so you can get a finger under the bottom edge.
0 2017/03/26 09:58:36
Pull to have more clearance at bolts and room to pull the cluster.
Pull to have more clearance at bolts and room to pull the cluster.
0 2017/03/26 09:55:56
0 2017/03/26 09:51:20
When removing watch the top to clear two tabs, then out enough to remove electrical connector.
When removing watch the top to clear two tabs, then out enough to remove electrical connector.
0 2017/03/26 09:48:34
Gently pull out to release these, that is the valet button at top of photo. Other side same location.
Gently pull out to release these, that is the valet button at top of photo. Other side same location.
0 2017/03/26 09:42:20
back of switch with arrow pointing to buld
back of switch with arrow pointing to buld
0 2017/03/23 06:12:05
How it inserts through circuit board
How it inserts through circuit board
0 2017/03/23 06:11:31
bulb from master window switch
bulb from master window switch
0 2017/03/23 06:10:54
Red goes under yellow
Red goes under yellow
0 2017/03/18 17:07:29
pull both tabs up and slide off the cover
pull both tabs up and slide off the cover
0 2017/03/18 17:05:46
press here to release the connector
press here to release the connector
0 2017/03/18 17:04:33
Hole is just beyond the point of insert
Hole is just beyond the point of insert
0 2017/03/18 16:58:19
small screw driver or similar tool under an edge and grab with fingers or gently with needle nose pliers.
small screw driver or similar tool under an edge and grab with fingers or gently with needle nose pliers.
0 2017/03/18 16:51:43
0 2017/03/12 09:36:42
0 2017/03/12 09:27:13
0 2017/03/12 09:23:45
0 2017/03/06 16:46:18
0 2017/03/06 16:46:16
Red trace wire is on the positive terminal.
Red trace wire is on the positive terminal.
0 2017/03/06 16:16:25
0 2017/03/06 16:14:46
The edge of speaker can be seen
The edge of speaker can be seen
0 2017/03/06 16:11:46
0 2017/02/18 13:57:29
Before- Broken hinge after disassembled.
Before- Broken hinge after disassembled.
0 2017/02/16 06:49:39
Repaired hinge.
Repaired hinge.
0 2017/02/16 06:48:22
pretty clean used part arrived from a 98 donor car
pretty clean used part arrived from a 98 donor car
0 2017/02/03 13:41:11
color of oil
color of oil
0 2016/04/10 15:06:41
Here is the fender right about the area from elbow to elbow looked just like the trunk.
Here is the fender right about the area from elbow to elbow looked just like the trunk.
0 2016/04/10 14:17:18
Cloudy day the dark is a dark cloud above and the right side is my house reflecting. A few imperfections but no longer embarrassing. A good 10 footer.
Cloudy day the dark is a dark cloud above and the right side is my house reflecting. A few imperfections but no longer embarrassing. A good 10 footer.
0 2016/04/10 14:16:52
Here is what it looked like when I picked it up on the trailer.
Here is what it looked like when I picked it up on the trailer.
0 2016/04/10 14:16:35
cut out pattern from computer monitor cable cover piece
cut out pattern from computer monitor cable cover piece
0 2016/03/31 19:30:35
Used heat gun to warm it up then bent and cooled against larger metal
Used heat gun to warm it up then bent and cooled against larger metal
0 2016/03/31 19:30:34
completed piece ready to glue
completed piece ready to glue
0 2016/03/31 19:30:32
Heat gun and pliers to bend, this type of plastic has a low heat point and very easy to shape, yet extremely ridged
Heat gun and pliers to bend, this type of plastic has a low heat point and very easy to shape, yet extremely ridged
0 2016/03/29 18:12:18
started with a simple outline, used a tapered drill to cut the hole then cut the two angled notches, then outside the line to an approximate edge to fold for the replacement I needed
started with a simple outline, used a tapered drill to cut the hole then cut the two angled notches, then outside the line to an approximate edge to fold for the replacement I needed
0 2016/03/29 18:12:17
Here is what it looked like finished
Here is what it looked like finished
0 2016/03/29 18:12:16
black wire exiting under the connector is added, soldered second pin in from corner between the plastic connector and circuit board then to junction on board
black wire exiting under the connector is added, soldered second pin in from corner between the plastic connector and circuit board then to junction on board
0 2016/03/27 18:39:01
two large silver spots are my first solder
two large silver spots are my first solder
0 2016/03/27 18:38:59
Found at lowes, had to remove about 3/4 of outer thread to get to fit. 10-32 internal screw.
Found at lowes, had to remove about 3/4 of outer thread to get to fit. 10-32 internal screw.
0 2016/03/26 08:22:38
New threads glued into place with JB weld
New threads glued into place with JB weld
0 2016/03/26 08:22:36