Jaguar Forums - Jaguar Enthusiasts Forum
0 2024/07/19 11:51:22
0 2020/10/27 23:23:11
0 2019/06/03 22:43:52
0 2019/05/22 13:49:16
0 2019/05/18 23:41:27
0 2019/05/18 23:40:32
0 2019/05/18 23:37:09
0 2019/05/02 13:24:03
0 2019/05/02 12:19:32
0 2019/03/23 08:40:14
0 2019/03/23 08:39:55
0 2019/03/15 14:21:05
Steering turned right
Steering turned right
0 2019/03/15 14:05:52
0 2019/03/15 13:51:10
0 2019/03/13 12:32:57
0 2019/03/13 12:32:41
0 2019/03/10 07:22:11
Camber changes with suspension movement
Camber changes with suspension movement
0 2019/03/10 07:15:45
Pictorial of the Mk2 front suspension
Pictorial of the Mk2 front suspension
0 2019/03/02 13:30:58
0 2019/02/27 12:00:25
Mk2
Mk2
0 2019/02/27 10:25:19
S Type
S Type
0 2019/02/27 10:24:44
0 2019/02/26 10:09:44
When refitting the solenoid, make sure both gaps either side of the balance wheel are even.
When refitting the solenoid, make sure both gaps either side of the balance wheel are even.
0 2019/02/16 13:01:25
Put the diode and its housing back together in the reverse order here is the screw that holds the terminal in place
Put the diode and its housing back together in the reverse order here is the screw that holds the terminal in place
0 2019/02/16 13:00:24
This is the diode, this needs to be taken out and flipped side for side, you can put a small dot with a marker pen on one side so you know which side is which if you drop it ! This is held in place with a spring, be careful when removing this not to break the plastic holder.
This is the diode, this needs to be taken out and flipped side for side, you can put a small dot with a marker pen on one side so you know which side is which if you drop it ! This is held in place with a spring, be careful when removing this not to break the plastic holder.
0 2019/02/16 12:57:51
Remove the screw that holds the terminal in place and carefully lift out the rectifier housing, this can be quite brittle, so be careful
Remove the screw that holds the terminal in place and carefully lift out the rectifier housing, this can be quite brittle, so be careful
0 2019/02/16 12:55:49
Undo the 2 locating pegs and carefully pull the solenoid out of the way, do not pull the wires too much especially where they join the coil
Undo the 2 locating pegs and carefully pull the solenoid out of the way, do not pull the wires too much especially where they join the coil
0 2019/02/16 12:54:27
Remove the insulating sleeve, screwdriver is pointing at the disc which is a diode, this has to be flipped round to face the opposite way
Remove the insulating sleeve, screwdriver is pointing at the disc which is a diode, this has to be flipped round to face the opposite way
0 2019/02/16 12:52:38
0 2019/02/16 12:51:51
Next remove the backplate by lifting it from the dowels
Next remove the backplate by lifting it from the dowels
0 2019/02/16 12:51:00
Backplate removed
Backplate removed
0 2019/02/16 12:50:31
Then remove the back plate
Then remove the back plate
0 2019/02/16 12:49:52
Remove the 4 screws and link from the rear of the clock
Remove the 4 screws and link from the rear of the clock
0 2019/02/16 12:49:07
0 2019/02/12 13:36:28
0 2019/02/12 13:14:38
Rebuilt
Rebuilt
0 2019/01/30 09:29:21
0 2019/01/30 09:28:19
How they started off
How they started off
0 2019/01/30 09:27:57
0 2019/01/13 22:25:58