Jaguar Forums - Jaguar Enthusiasts Forum
0 2025/09/13 08:00:51
0 2025/09/13 07:59:35
0 2025/09/13 07:55:06
0 2025/09/13 07:53:37
0 2025/09/13 07:53:04
0 2024/12/06 21:41:54
0 2024/09/13 12:22:27
0 2024/09/13 12:22:26
0 2024/09/13 12:21:14
0 2024/09/13 12:21:12
0 2024/09/13 07:41:20
0 2024/09/13 07:41:19
0 2024/09/13 07:41:18
A quick Google shows me that the driver side takes a 22" and the passenger side has a 19"
A quick Google shows me that the driver side takes a 22" and the passenger side has a 19"
0 2023/03/30 02:38:16
0 2023/03/04 14:22:51
0 2023/03/04 14:22:22
Using the metal ruler to hold down the rubber so I could place and secure the cap.
Using the metal ruler to hold down the rubber so I could place and secure the cap.
0 2023/03/04 14:21:02
Using the oversize cotton swabs, I cleaned it out.
Using the oversize cotton swabs, I cleaned it out.
0 2023/03/04 14:19:17
When removed, I found the issue. Sure enough there is the rip.
When removed, I found the issue. Sure enough there is the rip.
0 2023/03/04 14:17:49
0 2023/03/04 14:17:26
Using the pick, you can pull the clips away while placing a slight upward pressure to remove the cap.
Using the pick, you can pull the clips away while placing a slight upward pressure to remove the cap.
0 2023/03/04 14:15:44
Now you can see that there is a rubber seal which allows clearance to swap out cap.
Now you can see that there is a rubber seal which allows clearance to swap out cap.
0 2023/03/04 14:14:33
You now have easy access to the cap.
You now have easy access to the cap.
0 2023/03/04 14:13:22
Carefully spin tubings out of the way to allow access.
Carefully spin tubings out of the way to allow access.
0 2023/03/04 14:11:59
Remove the two cooling lines to give room to remove the breather line. You need to press in on the clip, squeeze the two buttons on the side and then carefully pull off. There will be fluid so I have placed some paper towel under fittings to capture.
Remove the two cooling lines to give room to remove the breather line. You need to press in on the clip, squeeze the two buttons on the side and then carefully pull off. There will be fluid so I have placed some paper towel under fittings to capture.
0 2023/03/04 14:08:53
Squeeze together at the ridges areas while slight pressure inward, then pull and it should pop off. Do this on both sides.
Squeeze together at the ridges areas while slight pressure inward, then pull and it should pop off. Do this on both sides.
0 2023/03/04 14:07:09
The breather tube uses a slightly different means of securing but it is still the same principle.
The breather tube uses a slightly different means of securing but it is still the same principle.
0 2023/03/04 14:05:31
The vacuum tubes can be disconnected by squeezing tabs together and softly pulling out of fitting.
The vacuum tubes can be disconnected by squeezing tabs together and softly pulling out of fitting.
0 2023/03/04 14:00:49
The clips attached to the battery tray can be popped open by pressing together and popping the bottom.
The clips attached to the battery tray can be popped open by pressing together and popping the bottom.
0 2023/03/04 13:58:42
You now have easy access to the area and to remove tubing.
You now have easy access to the area and to remove tubing.
0 2023/03/04 13:57:48
0 2022/03/26 18:39:40
0 2022/03/26 10:32:42
0 2022/02/21 18:34:51
0 2022/02/21 18:34:30
0 2022/02/21 18:30:22
0 2022/02/21 18:28:55
0 2022/02/21 18:25:33
0 2022/02/21 18:24:08
0 2022/02/21 18:21:12
0 2022/02/21 18:10:35