Jaguar Forums - Jaguar Enthusiasts Forum
0 2024/05/07 10:50:24
0 2024/05/07 10:50:12
0 2024/05/07 10:50:02
0 2024/05/07 10:49:52
0 2024/05/06 03:51:58
0 2024/05/04 14:23:06
0 2024/05/04 14:22:58
0 2024/05/04 13:54:37
0 2023/05/24 04:58:46
0 2023/05/24 04:58:37
0 2022/08/21 06:34:49
0 2021/10/29 06:11:31
0 2021/10/29 06:10:35
0 2021/09/24 04:15:21
0 2021/09/24 04:14:43
0 2021/09/24 04:14:37
0 2021/09/24 04:14:30
0 2021/09/24 04:13:56
0 2021/09/24 04:13:06
0 2021/09/24 04:12:56
0 2021/09/24 04:12:47
0 2021/09/24 04:11:48
0 2021/09/24 04:11:16
0 2020/02/22 04:53:01
0 2020/02/22 04:52:06
It's a little hard to tell here but it's flush.
It's a little hard to tell here but it's flush.
0 2020/02/22 04:49:30
You can see how the tool fits. All it took was a light tap using a rubber mallet and the seal slid right in.
You can see how the tool fits. All it took was a light tap using a rubber mallet and the seal slid right in.
0 2020/02/22 04:48:28
This worked great to pull the old seal.
This worked great to pull the old seal.
0 2020/02/22 04:46:05
This view is the part that slides in. The front crank seal slides over the smaller part of the tool and the outer portion of the seal sits on the shoulder that you see.
This view is the part that slides in. The front crank seal slides over the smaller part of the tool and the outer portion of the seal sits on the shoulder that you see.
0 2020/02/22 04:44:15
The button even had a little o-ring to keep it in place.
The button even had a little o-ring to keep it in place.
0 2020/02/22 04:43:02
0 2020/02/22 04:41:24
Looking up from below the car.
Looking up from below the car.
0 2020/02/22 04:39:46
Model 840781
Model 840781
0 2020/02/22 04:38:20
Here you can see the bolt sticking out through the window. When you turn the crank, it hits the housing and locks it. I wanted to make sure it wouldn't break or bend so I used the strongest bolt I could get....grade 12.9
Here you can see the bolt sticking out through the window. When you turn the crank, it hits the housing and locks it. I wanted to make sure it wouldn't break or bend so I used the strongest bolt I could get....grade 12.9
0 2020/02/22 04:35:39
0 2020/02/22 04:34:26
0 2020/02/22 04:34:22
3/8" ratchet with normal sized 15mm socket.
3/8" ratchet with normal sized 15mm socket.
0 2020/02/22 04:33:15
It's on the front side of the bellhousing....looking from underneath.
It's on the front side of the bellhousing....looking from underneath.
0 2020/02/22 04:31:27
I tucked the cardboard over the radiator support. It stayed put the entire time.
I tucked the cardboard over the radiator support. It stayed put the entire time.
0 2020/02/22 04:29:25
Took the picture too late but you can see the two bolts that hold it in.
Took the picture too late but you can see the two bolts that hold it in.
0 2020/02/22 04:28:34