Jaguar Forums - Jaguar Enthusiasts Forum
0 2026/03/06 04:45:33
0 2026/03/06 04:44:54
0 2026/03/06 04:44:14
0 2026/03/06 04:41:57
0 2026/03/06 04:41:20
0 2025/11/11 04:01:47
0 2025/10/02 20:15:28
0 2025/10/02 20:15:24
0 2025/10/02 20:15:18
0 2025/10/02 20:15:12
0 2025/10/02 20:15:06
Again, this is from 97 ym book but diagram #3 shows two matching parts, oem #mna3504ab , quantity 4 (4 total, 2 each side) but could absolutely be replaced with an elongated bushing meant to replace two bushings with one.
Again, this is from 97 ym book but diagram #3 shows two matching parts, oem #mna3504ab , quantity 4 (4 total, 2 each side) but could absolutely be replaced with an elongated bushing meant to replace two bushings with one.
0 2025/09/28 20:54:51
One of my new Dorman brand replacement rear sway bar end links, if you look closely, the middle groove in the rubber bushing is of slightly smaller diameter, which I believe is supposed to be pressed into the control arm mount thus leaving equal portions of rubber bushing both above and below mount, as opposed to using a two piece setup.
One of my new Dorman brand replacement rear sway bar end links, if you look closely, the middle groove in the rubber bushing is of slightly smaller diameter, which I believe is supposed to be pressed into the control arm mount thus leaving equal portions of rubber bushing both above and below mount, as opposed to using a two piece setup.
0 2025/09/28 20:33:46
One of my oem rear sway bar links, showing rubber above and below control arm mount(previously mistaken for sway bar)
One of my oem rear sway bar links, showing rubber above and below control arm mount(previously mistaken for sway bar)
0 2025/09/28 20:30:49
0 2025/09/28 18:27:20
0 2025/08/19 11:34:22
0 2025/08/19 11:15:19
Outside view of hi mount plastic trim needed
Outside view of hi mount plastic trim needed
0 2025/08/13 15:11:11
Inside view of hi mount with cardboard
Inside view of hi mount with cardboard
0 2025/08/13 15:09:54
Drivers side triangle seat trim piece
Drivers side triangle seat trim piece
0 2025/08/13 15:08:49
0 2024/09/17 23:09:13
0 2024/09/17 23:08:45
0 2024/09/17 22:43:46
0 2024/09/17 22:43:32
0 2024/09/17 22:43:16
0 2024/09/17 22:43:09
0 2024/08/24 12:31:46
0 2024/08/24 12:31:40
0 2024/06/24 04:15:45
0 2024/06/24 04:14:50
0 2024/06/24 04:14:22
0 2024/06/12 00:18:42
0 2024/06/12 00:18:07
0 2024/06/11 04:37:29
The one I found for sale stamped with proper side numbers and has same curvature as mine as well as properly placed cutout
The one I found for sale stamped with proper side numbers and has same curvature as mine as well as properly placed cutout
0 2024/06/07 21:47:09
Sideish view to show curvature of bracket which is correct
Sideish view to show curvature of bracket which is correct
0 2024/06/07 21:44:13
Bracket from my car, looking at it from front of car, part number clearly printed, cutout towards outer edge for sway bar link
Bracket from my car, looking at it from front of car, part number clearly printed, cutout towards outer edge for sway bar link
0 2024/06/07 21:43:53
0 2024/06/07 18:32:39
Passengers side working room the way I parked like a dummy….whoops!
Passengers side working room the way I parked like a dummy….whoops!
0 2024/06/05 19:57:01
Bracket at my fingertips in wrong side causing bend in bracket to be in wrong orientation, making gap between both brackets too wide
Bracket at my fingertips in wrong side causing bend in bracket to be in wrong orientation, making gap between both brackets too wide
0 2024/06/05 19:53:56