Cant clip in seatbelt! Help! - Jaguar Forums - Jaguar Enthusiasts Forum

Go Back   Jaguar Forums - Jaguar Enthusiasts Forum > Jaguar Models ( Modern ) > X-Type ( X400 )
Log In 

X-Type ( X400 ) 2001 - 2009
Sponsored by Jagbits
Click Here

Cant clip in seatbelt! Help!

LinkBack Thread Tools Search this Thread
Old 10-01-2012, 03:46 PM
Junior Member
Join Date: Aug 2012
Location: Dublin, Ireland
Posts: 28
Thanked 1 Time in 1 Post
Default Cant clip in seatbelt! Help!

Hey everyone!, Loving my X, Ive had it 3 weeks now and its a dream to drive, I have a problem with the ambient temp sensor and have ordered a replacement, i plan to install that myself, Found some good guides on this site for doing that, But now today i have a new problem, I cant get the drivers Buckle to clip in, The button is stuck half way down and is not springing back up, I can manually hook something into the button and release it, and this lets me plug the belt back in, But now each time i have to manually "reset" the button and its getting harder to do each time, Im sure this is covered on my warranty but my garage is 200 miles away and would mean a day off work, and i cant afford to do that, Its rattling so i suspect there is a bit of plastic loose in it.... any advice would be appriciated
2004 Jaguar X-Type 2.0D Classic
Reply With Quote
Old 10-01-2012, 04:20 PM
disguay's Avatar
Veteran Member
Join Date: May 2011
Location: fort collins, CO
Posts: 1,109
Thanked 167 Times in 144 Posts

This sometimes happens if you get stuff stuck in the clip. I would recommend just unbolting it and shaking it out. If that doesn't fix it, salvage yard or ebay and get a new/used one. Shouldn't be too expensive of a fix
2002 3.0 sport 5spd with 128k and counting...
Currently on 18's, lowered, with SPC rear UCA's, dual resonator delete, and some bump (2 12's) in the trunk!
Reply With Quote
Old 10-01-2012, 08:18 PM
Thermo's Avatar
Veteran member
Join Date: May 2008
Location: Great Mills, MD
Posts: 9,575
Thanks: 0
Thanked 2,169 Times in 1,870 Posts

Based on your situation, I would say you will be better suited to simply spend the little bit on a new belt end and then install it yourself. Installing the belt is easy. The hardest part of it all will probably be accessing the end of the belt with the torx bit bolt. To remove the driver's seat, you will need an open end wrench to remove the 2 bolts on the front side of the seat and then the 4 bolts in the rear (2 on each side, about 4 cm apart, 1 in front of the other). With the seat out of the way, you will probably need a T55 torx bit to get the seat belt end out of the way. All said, you can probably get this done in an hour or so. Most of the time will be spent dealing with the 4 bolts on the back side of the seat. You will only be able to get about a 1/4 turn on the front bolts in the back. The rear most bolts are not too bad and you can get just under a 1/2 turn before needing to reposition the wrench.
Chris "Thermo" Coleman and Jackie, the 12 XJ
Reply With Quote
The Following User Says Thank You to Thermo For This Useful Post:
Lcgi (10-01-2012)
Old 10-02-2012, 03:16 AM
GGG's Avatar
GGG GGG is online now
Join Date: Dec 2011
Location: Durham, UK
Posts: 86,004
Thanked 6,749 Times in 5,784 Posts

The seatbelt buckle not only needs to clip in securely but you must also be absolutely confident it can always be undone in an emergency. Your faulty buckle no longer has that reliability and should be replaced.

If you intend to source a used buckle, be aware they are handed (LH and RH are not interchangeable) and in addition to the three colour options to match the trim, there are three Part Number changes according to VIN range.

This old thread highlights some of the difficulties with a used replacement:

If the sealtbelt is covered under warranty, it might be prudent to do the trip to your garage.

2007 XK 4.2 Coupe

Reply With Quote
Old 10-14-2012, 02:11 PM
Junior Member
Join Date: Aug 2012
Location: Dublin, Ireland
Posts: 28
Thanked 1 Time in 1 Post

Thanks everyone for your replies, ended up bringing it back to the garage and they dismantled the buckle and removed a piece of plastic that was stuck in it, button is working fine now, thankfully it didn't have to be replaced
2004 Jaguar X-Type 2.0D Classic
Reply With Quote

Similar Threads
Thread Thread Starter Forum Replies Last Post
Airbag warning light with code B0070 Jpav27 XK / XKR ( X150 ) 8 03-21-2016 03:18 PM
Rear view mirror : The Saga Continues King Charles XJ XJ8 / XJR ( X308 ) 6 10-16-2015 01:25 AM
Rear Air Suspension Ride Height Fault dmatthewman XJ XJ6 / XJ8 / XJR ( X350 & X358 ) 1 09-30-2015 10:10 AM

2005, assembly, belt, buckle, button, jaguar, jagusr, powered, replace, seat, seatbelt, stuck, type, vbulletin, xtype

Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)
Thread Tools Search this Thread
Search this Thread:

Advanced Search

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are On
Pingbacks are On
Refbacks are On

All times are GMT -5. The time now is 02:22 AM.

JAGUAR and its logo are the registered trademarks of Jaguar Cars Limited. Jaguar Cars Limited is not affiliated with