Jaguar Forums - Jaguar Enthusiasts Forum
0 2020/12/27 05:18:06
0 2020/12/27 05:19:29
0 2020/12/27 05:20:00
0 2020/12/27 05:20:39
Interestingly, these brand new liners are not yet honed for oil retention. Luckily I have a Flex-Hone in stock for this requirement, if a new replacement liner is needed.
Interestingly, these brand new liners are not yet honed for oil retention. Luckily I have a Flex-Hone in stock for this requirement, if a new replacement liner is needed.
0 2020/12/31 06:12:19
0 2020/12/31 06:12:58
0 2020/12/31 06:13:36
0 2020/12/31 06:14:09
0 2020/12/31 06:32:16
0 2020/12/31 06:32:47
0 2020/12/31 06:33:18
0 2021/01/01 11:03:41
0 2021/01/03 05:43:27
0 2021/01/03 05:44:08
0 2021/01/07 23:28:07
Socket and long lever on the crank pulley
Socket and long lever on the crank pulley
0 2021/01/14 06:49:20
showing the starter motor position
showing the starter motor position
0 2021/01/14 06:50:04
0 2021/01/17 00:06:35
0 2021/01/17 00:07:18
0 2021/01/28 11:50:43
0 2021/01/28 11:50:58
0 2021/01/28 11:51:13
The two shelves plus the tongue, shelf 2 on the left, shelf 1 in the middle
The two shelves plus the tongue, shelf 2 on the left, shelf 1 in the middle
0 2021/01/29 23:45:00
Gearbox spring shaft and tail. The propshaft cannot be unbolted unless shelf 2 is removed
Gearbox spring shaft and tail. The propshaft cannot be unbolted unless shelf 2 is removed
0 2021/01/29 23:46:55
Place the second jack just ahead of the large nut on the tongue, then undo all the nuts and bolts you can see in the photo. Do not lose the special oval washers, as they cover the adjustment holes on the shelf!
Place the second jack just ahead of the large nut on the tongue, then undo all the nuts and bolts you can see in the photo. Do not lose the special oval washers, as they cover the adjustment holes on the shelf!
0 2021/01/29 23:47:27
0 2021/02/12 00:22:47
Cold start switch and tell-tale. Also a tell-tale for the main electric fan
Cold start switch and tell-tale. Also a tell-tale for the main electric fan
0 2021/02/12 03:38:53
0 2021/02/12 03:39:38
Access with the driveshaft, front shocker and lower wishbone disconnected
Access with the driveshaft, front shocker and lower wishbone disconnected
0 2021/02/19 00:28:03
Access with exhaust disconnected. showing caliper in the process of being unbolted. Note the lower wishbone has to be swung right down to get the disc off
Access with exhaust disconnected. showing caliper in the process of being unbolted. Note the lower wishbone has to be swung right down to get the disc off
0 2021/02/19 00:30:58
Caliper in the process of being wriggled free
Caliper in the process of being wriggled free
0 2021/02/19 00:33:24
Full Flow oil filter casting general view. Note huge threaded plug at bottom
Full Flow oil filter casting general view. Note huge threaded plug at bottom
0 2021/02/23 08:34:35
Close up of internal oil relief valve. If the cooler gets blocked the internal pressure forces open this valve to allow high pressure oil to the engine.
Close up of internal oil relief valve. If the cooler gets blocked the internal pressure forces open this valve to allow high pressure oil to the engine.
0 2021/02/23 08:35:07
Valve in closed position
Valve in closed position
0 2021/02/23 08:35:48
Valve in opened position (pushed open against the spring)
Valve in opened position (pushed open against the spring)
0 2021/02/23 08:36:21
Close up of valve in closed position. This valve assembly, as shown on its own in Andrew's photo (first photo in text above) has to be pressed into position in the casting by unscrewing the large plug, pressing in the valve, then replacing the plug.
Close up of valve in closed position. This valve assembly, as shown on its own in Andrew's photo (first photo in text above) has to be pressed into position in the casting by unscrewing the large plug, pressing in the valve, then replacing the plug.
0 2021/02/23 08:36:58
Close up of header tank
Close up of header tank
0 2021/02/28 22:28:38
The finished system
The finished system
0 2021/02/28 22:29:22
0 2021/02/28 22:30:04
Close up of header tank feed into T piece in heater return
Close up of header tank feed into T piece in heater return
0 2021/02/28 22:30:39