Jaguar Forums - Jaguar Enthusiasts Forum
pin numbering at coil connector
pin numbering at coil connector
0 2021/02/08 10:52:31
0.6second view of measuring continuity of white wire from Pin 18 and the opposite end of the white wire at the engine
0.6second view of measuring continuity of white wire from Pin 18 and the opposite end of the white wire at the engine
0 2021/02/08 10:52:30
Noid light installed in 1A injector socket
Noid light installed in 1A injector socket
0 2021/02/08 10:52:28
0.6 ohms measured at the wiring harness at the engine
0.6 ohms measured at the wiring harness at the engine
0 2021/02/08 10:52:27
red wire inserted into white wire pin 18
red wire inserted into white wire pin 18
0 2021/02/08 10:52:25
Fuel Injection ECU connector White wire is the pin bottom right
Fuel Injection ECU connector White wire is the pin bottom right
0 2021/02/08 10:52:23
0 2021/02/08 10:52:21
Pittsburg Noid Light Kit. Bosch2 light has the correct pins
Pittsburg Noid Light Kit. Bosch2 light has the correct pins
0 2021/02/08 10:52:19
0 2021/02/08 10:19:30
0 2021/02/02 14:25:47
fuse panel with access cover removed.
fuse panel with access cover removed.
0 2021/02/02 14:25:45
Right side A/C vent panel
Right side A/C vent panel
0 2021/02/02 14:25:44
Fuel inertia switch
Fuel inertia switch
0 2021/02/02 14:25:42
Looking up at the fuse panel cover
Looking up at the fuse panel cover
0 2021/02/02 14:25:40
Wire color code
Wire color code
0 2021/02/01 18:08:20
Wiring diagram for injectors
Wiring diagram for injectors
0 2021/02/01 18:08:18
Fuel Injection wiring schematic showing Feedback Monitor
Fuel Injection wiring schematic showing Feedback Monitor
0 2021/02/01 18:08:17
Fuel Injection Component Location
Fuel Injection Component Location
0 2021/02/01 18:08:16
My description of ECU pins
My description of ECU pins
0 2021/02/01 18:08:14
EFI wiring diagram for 1990 XJS
EFI wiring diagram for 1990 XJS
0 2021/02/01 18:08:13
Spark Tester installed inline at spark plug 2B for ease of access.
Spark Tester installed inline at spark plug 2B for ease of access.
0 2021/02/01 18:08:12
0 2021/01/29 11:03:10
This is the condition of the inlet air tube where it connects to the throttle body. I don't know if the broken section pre-existed the independent changing the water pump or not. I don't think they loosened the clamp at the throttle body until after trying to pull it off. I bought a replacement.
This is the condition of the inlet air tube where it connects to the throttle body. I don't know if the broken section pre-existed the independent changing the water pump or not. I don't think they loosened the clamp at the throttle body until after trying to pull it off. I bought a replacement.
0 2021/01/29 11:02:05
0 2021/01/29 10:56:46
The alignment pin at the bottom of each manifold to the block and the bolt at the bottom of the manifold that connects to the supercharger is also seen in this photo.
The alignment pin at the bottom of each manifold to the block and the bolt at the bottom of the manifold that connects to the supercharger is also seen in this photo.
0 2021/01/29 10:56:45
You can see the valley hose on the left side of this photo after it made the S-Curve
You can see the valley hose on the left side of this photo after it made the S-Curve
0 2021/01/29 10:47:30
The valley hose running from the back of the engine along the left side of the left side intake manifold to the front, S-curves to the right side of the throttle body.
The valley hose running from the back of the engine along the left side of the left side intake manifold to the front, S-curves to the right side of the throttle body.
0 2021/01/29 10:36:43
The black clip seen sitting on top of the engine oil cooler fits between the cooler and the flange seen on the tube. The C2Z18658 short black plastic tube plugs into the port on the back of the water pump and slides over the the metal tube seen here.
The black clip seen sitting on top of the engine oil cooler fits between the cooler and the flange seen on the tube. The C2Z18658 short black plastic tube plugs into the port on the back of the water pump and slides over the the metal tube seen here.
0 2021/01/29 10:22:02
I am not sure how they managed this, but the o-ring was both pinched and cut.
I am not sure how they managed this, but the o-ring was both pinched and cut.
0 2021/01/29 10:09:13
The source of the leak. This was a new pipe installed incorrectly by the Independent in August.
The source of the leak. This was a new pipe installed incorrectly by the Independent in August.
0 2021/01/29 10:09:12
I can't figure how they managed this, but the oring was pinched and cut. I don't know
I can't figure how they managed this, but the oring was pinched and cut. I don't know
0 2021/01/29 10:03:57
The cause of the leak was a new pipe incorrectly installed by the Independent.
The cause of the leak was a new pipe incorrectly installed by the Independent.
0 2021/01/29 10:03:55
0 2021/01/28 14:35:30
0 2021/01/28 14:35:29
0 2021/01/28 14:34:00
0 2021/01/28 14:32:59
I followed the suggestion to use an engine support bar to lift the supercharger and intake manifolds. It made the job MUCH easier. I used it again to suspend the supercharger while attaching the intake manifolds
I followed the suggestion to use an engine support bar to lift the supercharger and intake manifolds. It made the job MUCH easier. I used it again to suspend the supercharger while attaching the intake manifolds
0 2021/01/28 14:24:52
0 2021/01/24 14:45:47
0 2021/01/24 14:45:45
0 2021/01/24 14:35:35