Jaguar Forums - Jaguar Enthusiasts Forum
Resettable fuses
Resettable fuses
0 2019/08/06 09:15:10
Modified RCCM
Modified RCCM
0 2019/08/06 09:15:19
0 2019/08/06 09:15:25
0 2019/08/06 09:15:34
0 2019/08/06 09:15:46
0 2019/08/07 12:35:55
0 2019/08/07 12:36:07
0 2019/08/07 12:36:22
0 2019/08/11 11:41:59
0 2019/08/11 11:42:11
0 2019/08/11 11:42:47
0 2019/08/12 05:33:38
0 2019/08/13 09:19:30
The baffles are in the top half of the can
The baffles are in the top half of the can
0 2019/08/13 09:19:44
0 2019/08/13 09:20:03
0 2019/08/14 06:42:16
0 2019/08/26 06:20:12
0 2019/08/26 06:35:26
Both ends were toast
Both ends were toast
0 2019/09/03 16:29:04
Toast!
Toast!
0 2019/09/03 16:29:46
Rear lower outer ball joint bushing where it connects to spindle
Rear lower outer ball joint bushing where it connects to spindle
0 2019/09/03 16:30:20
Rear upper ball joint
Rear upper ball joint
0 2019/09/03 16:30:57
0 2019/09/03 16:31:37
0 2019/09/03 16:32:16
This seems to suggest there are two different bushings for the rear lower arm for the balljoint (spindle) end and the rear attaching arm bushing
This seems to suggest there are two different bushings for the rear lower arm for the balljoint (spindle) end and the rear attaching arm bushing
0 2019/09/04 06:31:43
Urethane
Urethane
0 2019/09/04 06:31:49
0 2019/09/04 06:31:53
0 2019/09/04 06:31:56
0 2019/09/04 06:32:00
This ad on ebay has the same lemforder bushings (same 37704 01) for the balljoint (spindle) end and the rear attaching point
This ad on ebay has the same lemforder bushings (same 37704 01) for the balljoint (spindle) end and the rear attaching point
0 2019/09/04 06:32:02
0 2019/09/04 06:53:21
It was a BITCH to get the axle to press out of the hub. Took several hours of banging, pressing, torching, penetration oil. It finally broke free
It was a BITCH to get the axle to press out of the hub. Took several hours of banging, pressing, torching, penetration oil. It finally broke free
0 2019/09/07 07:21:12
Punch the hub out but got stuck with a race on the shaft. No way to grab it. Ended up cutting two slots in it w cutting wheel and bearing separator grabbed it and pressed pushed it off. Finally
Punch the hub out but got stuck with a race on the shaft. No way to grab it. Ended up cutting two slots in it w cutting wheel and bearing separator grabbed it and pressed pushed it off. Finally
0 2019/09/07 07:21:38
Found previous own had both brake pads installed in the reverse positions so one pad (piston side) rode up and wore like this. Rotor had a ledge on it. More parts to buy.
Found previous own had both brake pads installed in the reverse positions so one pad (piston side) rode up and wore like this. Rotor had a ledge on it. More parts to buy.
0 2019/09/07 07:22:03
After installing first timkin bearing I noticed the second bearing had markings on it from SKF. First bearing had nothing. Figured it was a counterfeit so I returned it to Amazon and got a National bearing locally.
After installing first timkin bearing I noticed the second bearing had markings on it from SKF. First bearing had nothing. Figured it was a counterfeit so I returned it to Amazon and got a National bearing locally.
0 2019/09/07 07:22:33
0 2019/09/07 07:22:40
Rear tie rods shot
Rear tie rods shot
0 2019/09/07 07:37:57
Rear Inner tie rod and new one
Rear Inner tie rod and new one
0 2019/09/07 07:38:17
Rear outer tie rod end and new one
Rear outer tie rod end and new one
0 2019/09/07 07:39:54
Rear upper control arm balljoint shot
Rear upper control arm balljoint shot
0 2019/09/07 07:40:26