Jaguar Forums - Jaguar Enthusiasts Forum
New rubber hoses connected to radiator.
New rubber hoses connected to radiator.
0 2022/07/31 13:15:13
Installed shifter mods.
Installed shifter mods.
0 2022/07/31 13:31:19
Modified bracket close up.
Modified bracket close up.
0 2022/07/31 13:31:26
Shifter bracket after welding a washer to catch new hole.
Shifter bracket after welding a washer to catch new hole.
0 2022/07/31 13:31:31
0 2022/08/03 12:30:00
0 2022/08/03 12:30:06
Stock pan
Stock pan
0 2022/08/07 04:12:20
My kitten Alice inspecting the work after the spicy cured.
My kitten Alice inspecting the work after the spicy cured.
0 2022/08/07 04:12:26
I jacked the pan and heat sink under the subframe while the epoxy cured to ensure there was good contact between them.
I jacked the pan and heat sink under the subframe while the epoxy cured to ensure there was good contact between them.
0 2022/08/07 04:12:30
0 2022/08/07 04:43:50
0 2022/08/07 15:19:01
Original crossmember with 1” square tube to space it away from the body.
Original crossmember with 1” square tube to space it away from the body.
0 2022/08/11 13:51:42
0 2022/08/11 13:51:50
Exhaust hitting the crossmember.
Exhaust hitting the crossmember.
0 2022/08/11 13:51:59
2nd attempt Modifying the crossmember (view is of the bottom like if you were under car looking up). You can see the outside of the crossmember now mounts flush against the body and the the center section where the transmission mount sits is stepped down 1” with the square tubing.
2nd attempt Modifying the crossmember (view is of the bottom like if you were under car looking up). You can see the outside of the crossmember now mounts flush against the body and the the center section where the transmission mount sits is stepped down 1” with the square tubing.
0 2022/08/11 13:53:57
And here the modified crossmember’s topside (side that installs against body). I again troweled the PU sealant onto the crossmember as an experiment with reducing NVH. I used a 3/16” v shaped trowel.
And here the modified crossmember’s topside (side that installs against body). I again troweled the PU sealant onto the crossmember as an experiment with reducing NVH. I used a 3/16” v shaped trowel.
0 2022/08/11 13:56:43
0 2022/08/13 15:02:18
Here is the TV Cable at the throttle, note the copper washers (in red circle), that’s where the ball stud mounts on the bottom side of the throttle disc, the ball stud attaches to the end of the cable with the black plastic clip (barely visible)
Here is the TV Cable at the throttle, note the copper washers (in red circle), that’s where the ball stud mounts on the bottom side of the throttle disc, the ball stud attaches to the end of the cable with the black plastic clip (barely visible)
0 2022/08/15 14:37:33
Here you can see the throttle valve bracket and how it’s screwed into the stock mounting post of the throttle disc.
Here you can see the throttle valve bracket and how it’s screwed into the stock mounting post of the throttle disc.
0 2022/08/15 14:37:36
This is the throttle valve (round shaft in red circle) , viewed with the transmission pan off. This is at the idle position, the lever is putting a small amount of pressure on the throttle valve and depressing it slightly. At full throttle, the throttle valve is fully depressed and becomes invisible.
This is the throttle valve (round shaft in red circle) , viewed with the transmission pan off. This is at the idle position, the lever is putting a small amount of pressure on the throttle valve and depressing it slightly. At full throttle, the throttle valve is fully depressed and becomes invisible.
0 2022/08/15 14:37:38
0 2022/08/27 15:58:46
0 2022/08/31 13:31:40
0 2022/08/31 13:34:49
0 2022/08/31 13:41:45
0 2022/08/31 13:42:01
0 2022/08/31 13:43:21
0 2022/09/04 11:51:12
0 2022/09/21 04:17:59
0 2022/10/10 12:16:20
0 2022/10/10 12:16:26
0 2022/11/08 08:49:45
0 2022/11/08 08:50:02
0 2022/11/11 15:12:46
0 2022/11/11 15:12:54
0 2022/11/12 16:13:01
0 2022/11/12 16:13:09
0 2022/11/16 17:41:02
0 2022/11/16 17:41:09
They are the same height but this photo is angled slightly to allow comparison of shape. The 2004r is black tranny in front—note how quickly is ramps down.
They are the same height but this photo is angled slightly to allow comparison of shape. The 2004r is black tranny in front—note how quickly is ramps down.
0 2022/11/21 07:56:01
0 2022/11/21 08:00:05