Jaguar Forums - Jaguar Enthusiasts Forum
The white plastic inser needs to be removed first. Don’t forget to put it back in later
The white plastic inser needs to be removed first. Don’t forget to put it back in later
0 2022/07/01 21:17:32
Easily done by releasing and pushing forward on the side tabs that hold it in place
Easily done by releasing and pushing forward on the side tabs that hold it in place
0 2022/07/01 21:17:40
Release the pins by gently without breaking levering the grey locking tab downwards and wiggle pin out backwards
Release the pins by gently without breaking levering the grey locking tab downwards and wiggle pin out backwards
0 2022/07/01 21:17:47
Need to remove blue and red wire. One for each coil of DVC subwoofer
Need to remove blue and red wire. One for each coil of DVC subwoofer
0 2022/07/01 21:17:57
0 2022/07/01 21:18:06
Posi taps to one of the channels. Yellow is negative
Posi taps to one of the channels. Yellow is negative
0 2022/08/05 23:55:16
Screwed into the back with 1cm long screws. Will leave 4 small holes if removed in the plastic backing but no one will ever see that area in reality unless you take your seats out of the car. Unit can also be tucked under the plastic seat backing without screwing but then quite low which is still fine.
Screwed into the back with 1cm long screws. Will leave 4 small holes if removed in the plastic backing but no one will ever see that area in reality unless you take your seats out of the car. Unit can also be tucked under the plastic seat backing without screwing but then quite low which is still fine.
0 2022/08/05 23:55:26
0 2022/08/05 23:55:34
0 2022/08/05 23:55:40
Original wiring is long enough without need to splice in any extension wiring. Seat is at maximum tilt and forward position so no chance to over tensioning the wire
Original wiring is long enough without need to splice in any extension wiring. Seat is at maximum tilt and forward position so no chance to over tensioning the wire
0 2022/08/05 23:55:47
0 2022/08/11 20:53:35
0 2022/08/11 20:53:45
0 2022/08/11 20:53:52
You will need to remove both the speaker baffle and the speakers and brace form the car
You will need to remove both the speaker baffle and the speakers and brace form the car
0 2022/08/14 05:34:10
Remove raised ring form back of speaker baffle for tweeter
Remove raised ring form back of speaker baffle for tweeter
0 2022/08/14 05:34:16
On arm of speaker brace could vibrate here so need treatment
On arm of speaker brace could vibrate here so need treatment
0 2022/08/14 05:34:21
Remove small partial raised ring from around the tweeter case
Remove small partial raised ring from around the tweeter case
0 2022/08/14 05:34:25
0 2022/08/14 05:34:34
0 2022/08/14 05:34:40
0 2022/08/14 05:34:45
0 2022/08/14 05:34:48
0 2022/08/14 05:34:52
0 2022/08/14 05:34:55
0 2022/08/14 05:35:00
0 2022/08/14 05:35:04
Extra felt pad attached here
Extra felt pad attached here
0 2022/08/14 05:35:10
0 2022/08/14 05:35:16
0 2022/08/14 05:35:23
Extra foam strips here
Extra foam strips here
0 2022/08/14 05:35:28
Wrap both hole at the base of the cubby flap
Wrap both hole at the base of the cubby flap
0 2022/08/14 05:35:34
Locating pins on cubby flap are felt wrapped
Locating pins on cubby flap are felt wrapped
0 2022/08/14 05:35:40
0 2022/08/14 15:43:53
Update -scrap the felt pads - use compressible foam weather proofing draught strips instead
Update -scrap the felt pads - use compressible foam weather proofing draught strips instead
0 2022/08/17 01:23:22
3/8 socket
3/8 socket
0 2022/08/19 21:57:14
This is the hole
This is the hole
0 2022/08/19 21:57:24
Ideal use a reverse hex bit but I didn’t have one. I carefully used just regular pliers being super careful not to slip or round the hex portion. Only do this after you have loosened the bigger nut behind.
Ideal use a reverse hex bit but I didn’t have one. I carefully used just regular pliers being super careful not to slip or round the hex portion. Only do this after you have loosened the bigger nut behind.
0 2022/08/19 21:57:44
0 2022/08/19 21:57:51
Interior window seal. Thought the problem was originally caused by some failure or compression of the felt liner but has nothing to do with this problem.
Interior window seal. Thought the problem was originally caused by some failure or compression of the felt liner but has nothing to do with this problem.
0 2022/08/19 21:57:58
Where the yellow arrow is
Where the yellow arrow is
0 2022/08/19 22:12:38
0 2022/08/21 02:44:42