Jaguar Forums - Jaguar Enthusiasts Forum
Rear of the projector.
Rear of the projector.
0 2021/01/04 20:47:14
Remove those two phillip's head screws.
Remove those two phillip's head screws.
0 2021/01/04 20:55:25
Remove this clip. It's the only thing holding the projector in place after removing the two bottom screws.
Remove this clip. It's the only thing holding the projector in place after removing the two bottom screws.
0 2021/01/04 20:57:08
You want to keep this thing around because it will help you determine how much you need to cut from the Morimoto projector.
You want to keep this thing around because it will help you determine how much you need to cut from the Morimoto projector.
0 2021/01/04 21:01:36
Behold the projector bowl with its cutoff shield and the solenoid. This is the low-beam position.
Behold the projector bowl with its cutoff shield and the solenoid. This is the low-beam position.
0 2021/01/04 21:04:08
This is the high beam position.
This is the high beam position.
0 2021/01/04 21:05:07
Gently pry it off. Requires very little strength.
Gently pry it off. Requires very little strength.
0 2021/01/04 21:06:27
Be very careful doing this. Do not start cutting until you are absolutely sure your outline is correct and centered.
Be very careful doing this. Do not start cutting until you are absolutely sure your outline is correct and centered.
0 2021/01/04 21:12:39
As you can see, I also took this opportunity to make a foreground limiter that will also allow the top clip to clamp on the projector and secure it in place.
As you can see, I also took this opportunity to make a foreground limiter that will also allow the top clip to clamp on the projector and secure it in place.
0 2021/01/04 21:19:58
I used a small microfibre towel to protect the projector bowl as I was making the reductions using a Dremel with a cutting disc.
I used a small microfibre towel to protect the projector bowl as I was making the reductions using a Dremel with a cutting disc.
0 2021/01/04 21:20:05
0 2021/01/04 21:46:05
0 2021/01/04 21:46:28
0 2021/01/04 21:48:43
0 2021/01/04 21:50:12
This is the bulb holder and it firmly secures the bulb to the projector.
This is the bulb holder and it firmly secures the bulb to the projector.
0 2021/01/04 21:51:37
Cable to adaptor.
Cable to adaptor.
0 2021/01/04 21:53:47
Ignitor adaptor on bulb. The housing tells you which way to twist to lock it in place.
Ignitor adaptor on bulb. The housing tells you which way to twist to lock it in place.
0 2021/01/04 21:54:13
0 2021/01/04 21:59:12
0 2021/01/04 22:00:47
0 2021/01/04 22:02:08
If you look closely, you notice both projectors have clear lenses instead of the fresnel lens the OE projector has.
If you look closely, you notice both projectors have clear lenses instead of the fresnel lens the OE projector has.
0 2021/01/04 22:07:43
What you see. there is the effect of the camera flash.
What you see. there is the effect of the camera flash.
0 2021/01/04 22:07:50
Without the flash, it's hard to see the projector in some images.
Without the flash, it's hard to see the projector in some images.
0 2021/01/04 22:07:57
Low beams. They are much much brighter than before.
Low beams. They are much much brighter than before.
0 2021/01/04 22:10:31
High beams. This all four projectors are my high beams. I would not want to be on the receiving end of these.
High beams. This all four projectors are my high beams. I would not want to be on the receiving end of these.
0 2021/01/04 22:11:48
This is stock HID projector. Front ¾ view.
This is stock HID projector. Front ¾ view.
0 2021/01/05 07:57:54
This
This
0 2021/01/05 07:58:01
0 2021/01/05 07:58:07
This is the projector from the back. You open it up by prying back the tabs you see on the top and bottom.
This is the projector from the back. You open it up by prying back the tabs you see on the top and bottom.
0 2021/01/05 07:58:12
0 2021/01/05 07:58:18
I placed the cut-off shield and foreground limiter on top of the projector bowl. As you can see, the original cut-off shield and foreground limiter are a static plate, they are fitted like a washer.
I placed the cut-off shield and foreground limiter on top of the projector bowl. As you can see, the original cut-off shield and foreground limiter are a static plate, they are fitted like a washer.
0 2021/01/05 08:07:49
This is the cut-off shield and foreground limiter being on the lens holder.
This is the cut-off shield and foreground limiter being on the lens holder.
0 2021/01/05 08:09:23
0 2021/01/05 08:35:23
Low beam only, standing to the left of the Jag.
Low beam only, standing to the left of the Jag.
0 2021/01/05 17:16:07
Low beam only, standing to the right of the Jag.
Low beam only, standing to the right of the Jag.
0 2021/01/05 17:16:13
Low beam + Mini HB LED high beam
Low beam + Mini HB LED high beam
0 2021/01/05 17:16:20
Low beam + Bi-xenon high beam.
Low beam + Bi-xenon high beam.
0 2021/01/05 17:16:26
Low beam + Bi-xenon high beam + Mini HB LED high beam
Low beam + Bi-xenon high beam + Mini HB LED high beam
0 2021/01/05 17:16:33
Dark road.
Dark road.
0 2021/01/05 17:19:04
The low beam alone already lights up the entire road.
The low beam alone already lights up the entire road.
0 2021/01/05 17:19:08