Jaguar Forums - Jaguar Enthusiasts Forum
This picture is of a single High beam projector aimed at the trees over there.
This picture is of a single High beam projector aimed at the trees over there.
0 2020/12/11 16:31:56
This picture is of a single High beam projector aimed at the vet's office, the angle points a little more skyward than other pictures.
This picture is of a single High beam projector aimed at the vet's office, the angle points a little more skyward than other pictures.
0 2020/12/11 16:32:03
This picture is of a single High beam projector aimed at the vet's office but closer at an angle that reflected more off the ground.
This picture is of a single High beam projector aimed at the vet's office but closer at an angle that reflected more off the ground.
0 2020/12/11 16:32:12
This picture is of a single High beam projector aimed straight towards the ground about 100 or 200 meters away from me.
This picture is of a single High beam projector aimed straight towards the ground about 100 or 200 meters away from me.
0 2020/12/11 16:32:19
This is a picture of a single reflector High beam for comparison, aimed by the Jag.
This is a picture of a single reflector High beam for comparison, aimed by the Jag.
0 2020/12/11 16:32:26
This is a picture of a both reflector High beams on for comparison, aimed by the Jag.
This is a picture of a both reflector High beams on for comparison, aimed by the Jag.
0 2020/12/11 16:32:32
Lift tabs. There's three on top, three on the bottom, and on on each side.
Lift tabs. There's three on top, three on the bottom, and on on each side.
0 2020/12/13 16:27:32
Pull assembly apart.
Pull assembly apart.
0 2020/12/13 16:28:07
The T-10 bulb holder twists off clockwise. This is a good time to replace the bulb with an LED.
The T-10 bulb holder twists off clockwise. This is a good time to replace the bulb with an LED.
0 2020/12/13 16:30:50
Pry the clip to disconnect the turn signal indicator connector.
Pry the clip to disconnect the turn signal indicator connector.
0 2020/12/13 16:31:20
First pull the blue clip by lifting from one side, the rest will come out. Then lift the two large tabs to unlock the connector.
First pull the blue clip by lifting from one side, the rest will come out. Then lift the two large tabs to unlock the connector.
0 2020/12/13 16:34:32
Top screw.
Top screw.
0 2020/12/13 16:38:02
Bottom screw. A magnetic screwdriver will make your life much easier on reassembly. You could also used tape or some super glue to hold the screw driver in place.
Bottom screw. A magnetic screwdriver will make your life much easier on reassembly. You could also used tape or some super glue to hold the screw driver in place.
0 2020/12/13 16:38:29
I find it's best to either pull on the left or right side of the reflector first. Trying to pull both at the same time is a wasted effort.
I find it's best to either pull on the left or right side of the reflector first. Trying to pull both at the same time is a wasted effort.
0 2020/12/13 16:40:20
Use a Dremel with a carbide bur to increase the diameter of the reflector's bulb holder hole. DO NOT grind the reflector part of the bulb holder hole.
Use a Dremel with a carbide bur to increase the diameter of the reflector's bulb holder hole. DO NOT grind the reflector part of the bulb holder hole.
0 2020/12/13 16:43:00
You don't need to grind down too much material. Just a little bit so that the threaded shaft can fit snugly on the plastic bulb holder.
You don't need to grind down too much material. Just a little bit so that the threaded shaft can fit snugly on the plastic bulb holder.
0 2020/12/13 16:43:18
Use four screws to secure the shroud to the projector.
Use four screws to secure the shroud to the projector.
0 2020/12/13 16:47:14
Supposedly the bottom side of the projector is the flat end, however, I found out that this doesn't mean it will be correctly aimed.
Supposedly the bottom side of the projector is the flat end, however, I found out that this doesn't mean it will be correctly aimed.
0 2020/12/13 16:47:30
Slip the projector inside the reflector.
Slip the projector inside the reflector.
0 2020/12/13 16:52:32
Righty tighty gets the projector shaft all the way out. By not wearing down on the reflector portion of the hole, it itself is screwed onto the projector.
Righty tighty gets the projector shaft all the way out. By not wearing down on the reflector portion of the hole, it itself is screwed onto the projector.
0 2020/12/13 16:52:58
0 2020/12/13 16:56:27
You may line up this tab (bottom one with the screw hole) with that empty space in the heat sink. This does not necessarily mean the projector will be correctly aligned.
You may line up this tab (bottom one with the screw hole) with that empty space in the heat sink. This does not necessarily mean the projector will be correctly aligned.
0 2020/12/13 16:58:57
This does not necessarily mean the projector will be correctly aligned.
This does not necessarily mean the projector will be correctly aligned.
0 2020/12/13 17:02:15
Snap the reflector-projector assembly in place, and then fasten the Phillip's head screws that hold the reflector in place.
Snap the reflector-projector assembly in place, and then fasten the Phillip's head screws that hold the reflector in place.
0 2020/12/13 17:05:20
This would be a good time to fit the headlight assembly as is (without the glass lens) and find some place dark to aim the projector and play with its orientation on the reflector.
This would be a good time to fit the headlight assembly as is (without the glass lens) and find some place dark to aim the projector and play with its orientation on the reflector.
0 2020/12/13 17:05:41
Using the tab or nub as a reference point, positive goes on the right, and negative to the left.
Using the tab or nub as a reference point, positive goes on the right, and negative to the left.
0 2020/12/13 17:08:49
Use a plier to gently pull the leads until they snap in place.
Use a plier to gently pull the leads until they snap in place.
0 2020/12/13 17:09:11
Connect the 9005/HB3 connector remember that the nub is grabbed by those two plastic tabs
Connect the 9005/HB3 connector remember that the nub is grabbed by those two plastic tabs
0 2020/12/13 17:09:30
It even makes the headlight look more modern!
It even makes the headlight look more modern!
0 2020/12/13 17:14:50
Factory low beam.
Factory low beam.
0 2020/12/13 17:28:59
Factory low beam + Morimoto Mini HB LEDProjector High beams
Factory low beam + Morimoto Mini HB LEDProjector High beams
0 2020/12/13 17:29:20
Stock low beam only.
Stock low beam only.
0 2020/12/15 18:18:40
Low beam + Morimoto Mini HB LED projector High beam
Low beam + Morimoto Mini HB LED projector High beam
0 2020/12/15 18:18:47
High Beam Only: Morimoto Mini HB LED projector
High Beam Only: Morimoto Mini HB LED projector
0 2020/12/15 18:22:36
0 2020/12/20 18:05:13
0 2020/12/20 18:05:21
0 2020/12/20 18:05:28
0 2020/12/20 18:05:36
0 2020/12/20 18:05:43
First I present the Morimoto 4TL-R Bi-xenon projector so that you guys can see what is being installed. Front ¾ view.
First I present the Morimoto 4TL-R Bi-xenon projector so that you guys can see what is being installed. Front ¾ view.
0 2021/01/04 20:46:58