Jaguar Forums - Jaguar Enthusiasts Forum
The upper seat plug is circled here there’s a lower seat plug on the frame too. I don’t apparently have a picture of it. And if I recall correctly from the wiring diagram, power comes into the lower seat elements goes through it then goes into the upper seat. Element goes through it, and then goes off to probably a ground.
The upper seat plug is circled here there’s a lower seat plug on the frame too. I don’t apparently have a picture of it. And if I recall correctly from the wiring diagram, power comes into the lower seat elements goes through it then goes into the upper seat. Element goes through it, and then goes off to probably a ground.
0 2025/01/24 07:12:58
0 2025/01/24 07:12:56
0 2025/01/24 07:12:54
The factory heated for the Lear high backed seats had side bolster heat (on the bottom at least). think the laster seats with separate head rests did not.
The factory heated for the Lear high backed seats had side bolster heat (on the bottom at least). think the laster seats with separate head rests did not.
0 2025/01/24 07:12:52
0 2025/01/24 06:40:57
0 2025/01/24 06:40:16
0 2025/01/24 06:40:07
0 2025/01/24 06:40:05
0 2024/12/11 14:05:22
0 2024/09/17 14:44:32
0 2024/09/16 12:53:02
0 2024/09/07 14:05:50
0 2024/09/07 13:45:57
0 2024/09/07 13:45:50
0 2024/09/07 13:45:42
0 2024/09/07 13:45:34
0 2024/09/07 13:45:23
0 2024/08/12 08:26:53
I caulked mine shut with clear-drying silicone
I caulked mine shut with clear-drying silicone
0 2024/08/12 08:26:49
3 more holes in top of side de-mister duct
3 more holes in top of side de-mister duct
0 2024/08/12 08:26:46
3 holes in bottom of side de-mister duct
3 holes in bottom of side de-mister duct
0 2024/08/12 08:26:44
0 2024/05/31 20:42:02
The bigger round hole is for the backlighting bulb, the smaller one is only used on the buttons that have an LED on indicator led like the seat heaters or Trac/ Off buttons
The bigger round hole is for the backlighting bulb, the smaller one is only used on the buttons that have an LED on indicator led like the seat heaters or Trac/ Off buttons
0 2024/05/31 20:41:58
The nub between the 2 small squares is what presses the underlying button (rear view of inner button).
The nub between the 2 small squares is what presses the underlying button (rear view of inner button).
0 2024/05/31 20:41:53
0 2024/05/31 20:41:50
This is the actual underlying button. When pressed the top 2 layers are flush with the 3rd layer. The button is spring loaded and does not stat in when pressed
This is the actual underlying button. When pressed the top 2 layers are flush with the 3rd layer. The button is spring loaded and does not stat in when pressed
0 2024/05/31 20:41:45
0 2024/05/31 20:41:40
The 4 channels it slides in should be clean and lubricated.
The 4 channels it slides in should be clean and lubricated.
0 2024/05/31 20:41:36
The middle buttons are similar but smaller and tend not to stick.
The middle buttons are similar but smaller and tend not to stick.
0 2024/05/31 20:41:31
Rear view of hazard switch inner button.
Rear view of hazard switch inner button.
0 2024/05/31 20:41:26
0 2024/03/10 11:58:36
0 2024/03/10 11:54:01
0 2024/03/03 20:00:41
0 2023/12/10 00:41:46
Kinked Antenna Mast
Kinked Antenna Mast
0 2023/12/10 00:41:43
0 2023/10/07 14:03:37
You put the double sided foam tape on the back side to seal against the firewall. That surface and the housing are slightly curved rather than flat, btw.
You put the double sided foam tape on the back side to seal against the firewall. That surface and the housing are slightly curved rather than flat, btw.
0 2023/05/27 22:07:38
See that water rectangular drain down in the middle? That was popped up and wouldn't stay down in place (meant to snap in place with 2 little nibs but heat/age deformed enough to not stay in anymore) so I used 4 thin strips of double sided mounting tape to stick in down in there better. Once again thinking better drainage means drier filter.
See that water rectangular drain down in the middle? That was popped up and wouldn't stay down in place (meant to snap in place with 2 little nibs but heat/age deformed enough to not stay in anymore) so I used 4 thin strips of double sided mounting tape to stick in down in there better. Once again thinking better drainage means drier filter.
0 2023/05/27 22:07:34
Plan on maybe replacing or touching up the double sided foam tape under this water shedder to keep it sealing well and keep your filter more dry-ish.
Plan on maybe replacing or touching up the double sided foam tape under this water shedder to keep it sealing well and keep your filter more dry-ish.
0 2023/05/27 22:07:31
Removing the water shedder was only one bolt and helped a lot
Removing the water shedder was only one bolt and helped a lot
0 2023/05/27 22:07:27