Jaguar Forums - Jaguar Enthusiasts Forum
This is a shot of the installation in the car. The red ring shows the top starter bolt hole, the bolt has been removed in this shot. NOTE to get even this amount of access, the gearbox has to be lowered as explained below.
This is a shot of the installation in the car. The red ring shows the top starter bolt hole, the bolt has been removed in this shot. NOTE to get even this amount of access, the gearbox has to be lowered as explained below.
0 2025/07/30 07:12:52
12 point (double hex) 7/16ths socket required on top starter bolt.
12 point (double hex) 7/16ths socket required on top starter bolt.
0 2025/07/30 07:03:03
Top starter bolt at the top; bottom starter bolt at the bottom of the photo
Top starter bolt at the top; bottom starter bolt at the bottom of the photo
0 2025/07/30 06:51:40
Out of focus close up of the top starter bolthead
Out of focus close up of the top starter bolthead
0 2025/07/30 06:51:35
0 2025/07/30 06:49:43
A cinch to undo!
A cinch to undo!
0 2025/07/14 02:59:55
Slots from below
Slots from below
0 2025/07/14 02:59:53
Access holes for rearmost slotted bolt holes
Access holes for rearmost slotted bolt holes
0 2025/07/14 02:59:49
Silly wings left over from the E type application cut off.
Silly wings left over from the E type application cut off.
0 2025/07/14 02:59:46
My metal effort which I would like to swap for your far nicer one.
My metal effort which I would like to swap for your far nicer one.
0 2025/07/12 12:36:53
3.5mm will be deep enough to cover the raised part. I am not using the D shape on the sensor, but a prong, and a shortened spindle with e a slot in the end.
3.5mm will be deep enough to cover the raised part. I am not using the D shape on the sensor, but a prong, and a shortened spindle with e a slot in the end.
0 2025/07/12 12:35:23
Shortened slotted spindle. You can order various types of spindle on the sensor itself.
Shortened slotted spindle. You can order various types of spindle on the sensor itself.
0 2025/07/05 12:58:21
Variohm unit
Variohm unit
0 2025/07/05 12:58:12
OEM support unchanged
OEM support unchanged
0 2025/07/03 00:11:09
Slot in back to accomodate tank strap
Slot in back to accomodate tank strap
0 2025/07/03 00:11:02
before and after
before and after
0 2025/07/03 00:10:59
fully modified
fully modified
0 2025/07/03 00:10:56
View from afar.
View from afar.
0 2025/06/29 13:45:51
Close up shot
Close up shot
0 2025/06/29 13:45:47
Finally done, ready for the cover
Finally done, ready for the cover
0 2025/06/29 13:45:44
The feed from the main tank has a WIX filter in it.
The feed from the main tank has a WIX filter in it.
0 2025/06/29 13:45:40
This shows the radiator bleed to the header tank, all uphill! A saloon crosspipe is used do no centre cap and spout, as wall collant addedd from the headert tank which is higher than the coolant system. Red tank is the atmospheric oveflow tank
This shows the radiator bleed to the header tank, all uphill! A saloon crosspipe is used do no centre cap and spout, as wall collant addedd from the headert tank which is higher than the coolant system. Red tank is the atmospheric oveflow tank
0 2025/06/28 06:54:40
Stainless tubes, one from the rad bleed, one to the atmo tak.
Stainless tubes, one from the rad bleed, one to the atmo tak.
0 2025/06/28 06:52:43
These are easy to removeas well, just squeeze the ears together.
These are easy to removeas well, just squeeze the ears together.
0 2025/06/22 00:33:09
0 2025/05/26 10:01:27
0 2025/05/24 09:46:37
0 2025/05/23 02:16:03
Wires from the OEM plug carefully labelled. It is all to eay to lose track of what goes where otherwise.
Wires from the OEM plug carefully labelled. It is all to eay to lose track of what goes where otherwise.
0 2025/05/23 02:02:07
0 2025/05/23 02:02:04
B bank even numbered batch wires this side of the plug
B bank even numbered batch wires this side of the plug
0 2025/05/23 02:02:01
A bank odd numbered batch wires this side of the plug
A bank odd numbered batch wires this side of the plug
0 2025/05/23 02:01:58
The connectors are labelled A or B, according to which bank they service, and one side of the plug handles the odd numbered injector batch, and one the even numbered batch.
The connectors are labelled A or B, according to which bank they service, and one side of the plug handles the odd numbered injector batch, and one the even numbered batch.
0 2025/05/23 02:01:55
On the left an OEM injector loom connector (eight wires, four live and four returns) labelled to show which injector batch they service. On the right, Deutsche connectors, one for each bank, each Deutsche connector has four pins, one +/- set for each batch of injectors.
On the left an OEM injector loom connector (eight wires, four live and four returns) labelled to show which injector batch they service. On the right, Deutsche connectors, one for each bank, each Deutsche connector has four pins, one +/- set for each batch of injectors.
0 2025/05/23 02:01:52
0 2025/05/20 12:37:03
0 2025/05/06 04:51:02
0 2025/05/05 23:18:09
0 2025/05/03 03:37:38
Grease coming out of the holes proving that the bearings are surrounded in grease, and more important, will have new grease pushed through them when regular servicing ss done.
Grease coming out of the holes proving that the bearings are surrounded in grease, and more important, will have new grease pushed through them when regular servicing ss done.
0 2025/04/27 02:31:08
You can just see the seal track nicely against the bracket, as a result of using shims to get the fit with no slop.
You can just see the seal track nicely against the bracket, as a result of using shims to get the fit with no slop.
0 2025/04/27 02:31:05
Depth of casting to bearing come shoulder. The actual bearing cone fills 11 mm of this depth. then comes the roller inner race
Depth of casting to bearing come shoulder. The actual bearing cone fills 11 mm of this depth. then comes the roller inner race
0 2025/04/27 02:17:36