Jaguar Forums - Jaguar Enthusiasts Forum
0 2023/06/08 09:54:46
0 2023/06/08 09:54:30
0 2023/06/08 09:54:04
0 2023/06/08 09:34:35
0 2023/06/08 09:21:15
0 2023/06/06 11:38:25
0 2023/06/06 11:38:16
0 2023/06/06 11:24:49
0 2023/06/06 11:15:41
0 2023/06/06 11:15:05
0 2023/06/06 11:12:20
0 2023/06/06 11:10:47
0 2023/06/06 11:06:54
0 2023/06/06 10:59:37
0 2023/06/06 10:54:52
0 2019/04/25 08:14:57
0 2019/04/18 04:45:51
0 2019/04/08 13:07:36
0 2019/04/08 13:07:27
0 2019/04/08 13:07:14
0 2019/04/08 08:32:31
0 2019/04/08 08:32:29
0 2019/04/03 07:13:17
0 2019/04/03 07:12:18
0 2019/03/26 04:52:25
0 2019/03/26 04:52:22
0 2019/03/26 04:52:20
Final product
Final product
0 2019/03/26 04:52:17
Button face fitted
Button face fitted
0 2019/03/26 04:52:14
The button base now sits proud of the trim.
The button base now sits proud of the trim.
0 2019/03/26 04:52:11
I've etched a pencil line where the ring needs to be sanded back to. I used a wide metal file, but a dremel, sandpaper, or careful handled razor knife would do the job.
I've etched a pencil line where the ring needs to be sanded back to. I used a wide metal file, but a dremel, sandpaper, or careful handled razor knife would do the job.
0 2019/03/26 04:52:09
Peel the old button face from the base and clean the surface thoroughly.
Peel the old button face from the base and clean the surface thoroughly.
0 2019/03/26 04:52:06
Base and spring.
Base and spring.
0 2019/03/26 04:52:03
Release the three equally spaced tabs to removed the button base.
Release the three equally spaced tabs to removed the button base.
0 2019/03/26 04:52:01
New 25mm button, slightly larger than the old. Some trimming will need to be done. It comes backed with a high quality 3M tape.
New 25mm button, slightly larger than the old. Some trimming will need to be done. It comes backed with a high quality 3M tape.
0 2019/03/26 04:51:58
Release button is held in by two small phillips screws.
Release button is held in by two small phillips screws.
0 2019/03/26 04:51:55
Plinth comes off by removing now accessible six 10mm nuts and some gentle prying.
Plinth comes off by removing now accessible six 10mm nuts and some gentle prying.
0 2019/03/26 04:51:52
Remove the retaining clips from trunk lid liner, and black plastic shroud around latch.
Remove the retaining clips from trunk lid liner, and black plastic shroud around latch.
0 2019/03/26 04:51:49
Definitely seen better days
Definitely seen better days
0 2019/03/26 04:51:46
Not bad for $0.
Not bad for $0.
0 2019/03/26 04:51:43