My STR on the dyno....
#1
My STR on the dyno....
http://www.youtube.com/watch?v=18aksH01IkM
http://www.youtube.com/watch?v=yxgdAUXld4E
Had to go back and run it again......The run stopped short of a full run due to the ABS light kicking on and the car going into Restricted Performance mode, as the car figured out the front tires where not moving.....
Went back and laid down some better numbers
Its funny to see, and NOT hear how loud the car is in stock form, but that shall change soon
http://www.youtube.com/watch?v=yxgdAUXld4E
Had to go back and run it again......The run stopped short of a full run due to the ABS light kicking on and the car going into Restricted Performance mode, as the car figured out the front tires where not moving.....
Went back and laid down some better numbers
Its funny to see, and NOT hear how loud the car is in stock form, but that shall change soon
#4
North Aurora huh...
Nice STR, real nice numbers, i'm working on getting the eurotoys pulley kit on as well, with the 2.5lb pulley, and it's being a huge PITA!!
I'm doing pulley kit, supercharger porting, iridium spark plugs, tstat from eurotoys, it's just been terrible. Currently having alot of trouble with the crank pulley. The puller pulled the threads out of one of the holes...so now debating about stopping to keep it running and paying a shop to take a stab at it, or using an air hammer to get it off Really has me frustrated
Nice STR, real nice numbers, i'm working on getting the eurotoys pulley kit on as well, with the 2.5lb pulley, and it's being a huge PITA!!
I'm doing pulley kit, supercharger porting, iridium spark plugs, tstat from eurotoys, it's just been terrible. Currently having alot of trouble with the crank pulley. The puller pulled the threads out of one of the holes...so now debating about stopping to keep it running and paying a shop to take a stab at it, or using an air hammer to get it off Really has me frustrated
Last edited by budsang1; 01-23-2010 at 05:43 PM.
#5
That sucks man......If you want I can recommend a great shop or 2 that will take care of that for you.....or even Euro toys, since they are in Elgin
Where abouts do you hang out.....ever come out to the burbs?
The is a forum that has a bunch of dif cars and set up meets and what not.....PM me if you want the scoop on that......
Nice to meet ya!
Where abouts do you hang out.....ever come out to the burbs?
The is a forum that has a bunch of dif cars and set up meets and what not.....PM me if you want the scoop on that......
Nice to meet ya!
#7
355rwhp 364wrtq that was w/Mina's cold air, and fresh tune up/fluids change.....
Next dyno pull will be with upper and lower pulley, and full exhaust from manifolds back....
Then port/polish of blower and full ecu tune......
Then I think that is all I can do to it.....
Wish I could change the rear end gear ratio......maybe a 3:55ish would be NICE!
Next dyno pull will be with upper and lower pulley, and full exhaust from manifolds back....
Then port/polish of blower and full ecu tune......
Then I think that is all I can do to it.....
Wish I could change the rear end gear ratio......maybe a 3:55ish would be NICE!
Trending Topics
#8
355rwhp 364wrtq that was w/Mina's cold air, and fresh tune up/fluids change.....
Next dyno pull will be with upper and lower pulley, and full exhaust from manifolds back....
Then port/polish of blower and full ecu tune......
Then I think that is all I can do to it.....
Wish I could change the rear end gear ratio......maybe a 3:55ish would be NICE!
Next dyno pull will be with upper and lower pulley, and full exhaust from manifolds back....
Then port/polish of blower and full ecu tune......
Then I think that is all I can do to it.....
Wish I could change the rear end gear ratio......maybe a 3:55ish would be NICE!
#10
They say it is between 8-10 rwhp per lb of boost......
As far as shops.....Take it to any Ford Shop that works on 03-04 Cobras and Lightnings, the puller for the top pulley is the same.....should be very cheap as I was quoted for 50 bucks to do it.....cheaper than getting a tool!
That will be done this wednesday....
As far as shops.....Take it to any Ford Shop that works on 03-04 Cobras and Lightnings, the puller for the top pulley is the same.....should be very cheap as I was quoted for 50 bucks to do it.....cheaper than getting a tool!
That will be done this wednesday....
#11
They say it is between 8-10 rwhp per lb of boost......
As far as shops.....Take it to any Ford Shop that works on 03-04 Cobras and Lightnings, the puller for the top pulley is the same.....should be very cheap as I was quoted for 50 bucks to do it.....cheaper than getting a tool!
That will be done this wednesday....
As far as shops.....Take it to any Ford Shop that works on 03-04 Cobras and Lightnings, the puller for the top pulley is the same.....should be very cheap as I was quoted for 50 bucks to do it.....cheaper than getting a tool!
That will be done this wednesday....
#13
I seem to notice that on here.....wish I was not the only one so if I run into problems someone would know the answer, but these are straight forward bolt ons.....cant wait til spring time to really make the cat have a nasty growl!
#14
#15
#17
Thread
Thread Starter
Forum
Replies
Last Post
clubairth1
S-Type / S type R Supercharged V8 ( X200 )
22
12-19-2022 07:08 PM
SoCalJagS
S-Type / S type R Supercharged V8 ( X200 )
4
09-27-2015 09:20 AM
Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)