Jaguar Forums - Jaguar Enthusiasts Forum
Top starter bolt at the top; bottom starter bolt at the bottom of the photo
Top starter bolt at the top; bottom starter bolt at the bottom of the photo
0 2025/07/30 06:51:40
Out of focus close up of the top starter bolthead
Out of focus close up of the top starter bolthead
0 2025/07/30 06:51:35
0 2025/07/30 06:49:43
A cinch to undo!
A cinch to undo!
0 2025/07/14 02:59:55
Slots from below
Slots from below
0 2025/07/14 02:59:53
Access holes for rearmost slotted bolt holes
Access holes for rearmost slotted bolt holes
0 2025/07/14 02:59:49
Silly wings left over from the E type application cut off.
Silly wings left over from the E type application cut off.
0 2025/07/14 02:59:46
These are easy to removeas well, just squeeze the ears together.
These are easy to removeas well, just squeeze the ears together.
0 2025/06/22 00:33:09
0 2025/05/26 10:01:27
0 2025/05/24 09:46:37
0 2025/05/23 02:16:03
Wires from the OEM plug carefully labelled. It is all to eay to lose track of what goes where otherwise.
Wires from the OEM plug carefully labelled. It is all to eay to lose track of what goes where otherwise.
0 2025/05/23 02:02:07
0 2025/05/23 02:02:04
B bank even numbered batch wires this side of the plug
B bank even numbered batch wires this side of the plug
0 2025/05/23 02:02:01
A bank odd numbered batch wires this side of the plug
A bank odd numbered batch wires this side of the plug
0 2025/05/23 02:01:58
The connectors are labelled A or B, according to which bank they service, and one side of the plug handles the odd numbered injector batch, and one the even numbered batch.
The connectors are labelled A or B, according to which bank they service, and one side of the plug handles the odd numbered injector batch, and one the even numbered batch.
0 2025/05/23 02:01:55
On the left an OEM injector loom connector (eight wires, four live and four returns) labelled to show which injector batch they service. On the right, Deutsche connectors, one for each bank, each Deutsche connector has four pins, one +/- set for each batch of injectors.
On the left an OEM injector loom connector (eight wires, four live and four returns) labelled to show which injector batch they service. On the right, Deutsche connectors, one for each bank, each Deutsche connector has four pins, one +/- set for each batch of injectors.
0 2025/05/23 02:01:52
0 2025/05/20 12:37:03
0 2025/05/06 04:51:02
0 2025/05/05 23:18:09
0 2025/05/03 03:37:38
Grease coming out of the holes proving that the bearings are surrounded in grease, and more important, will have new grease pushed through them when regular servicing ss done.
Grease coming out of the holes proving that the bearings are surrounded in grease, and more important, will have new grease pushed through them when regular servicing ss done.
0 2025/04/27 02:31:08
You can just see the seal track nicely against the bracket, as a result of using shims to get the fit with no slop.
You can just see the seal track nicely against the bracket, as a result of using shims to get the fit with no slop.
0 2025/04/27 02:31:05
Depth of casting to bearing come shoulder. The actual bearing cone fills 11 mm of this depth. then comes the roller inner race
Depth of casting to bearing come shoulder. The actual bearing cone fills 11 mm of this depth. then comes the roller inner race
0 2025/04/27 02:17:36
Hole from the outside
Hole from the outside
0 2025/04/27 02:17:33
Drill a hole, diameter 2.5mm, exactly 8.5 mm down from the top of the casting
Drill a hole, diameter 2.5mm, exactly 8.5 mm down from the top of the casting
0 2025/04/27 02:17:30
oil seal NOT in place
oil seal NOT in place
0 2025/04/27 02:13:05
oil seal in place
oil seal in place
0 2025/04/27 02:12:37
Hub casting on its side, wood dowel replaces pin, everything still in place
Hub casting on its side, wood dowel replaces pin, everything still in place
0 2025/04/27 02:00:50
This isfor the left hand side. The bracket interior length is the wood rod plus 6 thou.
This isfor the left hand side. The bracket interior length is the wood rod plus 6 thou.
0 2025/04/27 01:56:50
0 2025/04/27 01:53:45
0 2025/04/27 01:48:38
0 2025/04/27 01:17:28
And then clean out the old grease and all is ready to rebuild
And then clean out the old grease and all is ready to rebuild
0 2025/04/27 01:12:38
You need a long thinnish drift
You need a long thinnish drift
0 2025/04/27 01:12:00
0 2025/04/27 01:10:45
0 2025/04/27 00:55:07
0 2025/04/27 00:47:08
0 2025/04/27 00:45:09
Hub casting showing the lower fulcrum
Hub casting showing the lower fulcrum
0 2025/04/27 00:20:50