Jaguar Forums - Jaguar Enthusiasts Forum
0 2025/03/02 07:20:45
OEM dif to cage fixing bolt. Using a stud allows far deeper threading into the diff casing and more reliable clamping.
OEM dif to cage fixing bolt. Using a stud allows far deeper threading into the diff casing and more reliable clamping.
0 2025/03/01 02:19:44
Tapered washers to fit into the tapered hole in the cage
Tapered washers to fit into the tapered hole in the cage
0 2025/03/01 02:16:25
Studs screwed into the diff through the cage
Studs screwed into the diff through the cage
0 2025/03/01 02:16:21
Finished item.
Finished item.
0 2025/03/01 02:14:28
1/2 inch UNC studs into the diff, loctited in. taper washers and nylocs
1/2 inch UNC studs into the diff, loctited in. taper washers and nylocs
0 2025/03/01 02:14:25
0 2025/02/14 12:44:18
0 2025/02/14 12:44:15
0 2025/02/14 12:43:47
0 2025/02/14 06:34:22
0 2025/02/14 06:34:18
0 2025/02/14 06:34:15
0 2025/02/07 08:19:21
0 2025/02/03 05:41:07
0 2025/01/26 08:40:17
0 2025/01/26 08:40:14
0 2025/01/26 08:40:10
0 2025/01/22 08:13:58
0 2025/01/22 08:12:02
Close-up of the spliced OEM injector loom plug connected to the car loom.
Close-up of the spliced OEM injector loom plug connected to the car loom.
0 2025/01/22 07:44:02
Combined loom wires wrapped together and cable tied in place.
Combined loom wires wrapped together and cable tied in place.
0 2025/01/22 07:43:57
New loom being cable tied to the rail, NOT in the bottom of the V.
New loom being cable tied to the rail, NOT in the bottom of the V.
0 2025/01/22 07:43:52
0 2025/01/22 07:40:46
Front injector close-up
Front injector close-up
0 2025/01/22 07:40:42
Oetiker clamp on the injector, stainless fuel pipe clamp on the rail spigot
Oetiker clamp on the injector, stainless fuel pipe clamp on the rail spigot
0 2025/01/22 07:40:39
Front two injectors fitted after the back five each side have been fitted
Front two injectors fitted after the back five each side have been fitted
0 2025/01/22 07:40:36
Offering up the rail
Offering up the rail
0 2025/01/22 07:40:31
0 2025/01/16 05:17:30
0 2025/01/16 05:15:03
0 2025/01/16 05:05:16
It would need about an inch welded in a shown in blue
It would need about an inch welded in a shown in blue
0 2025/01/15 12:54:21
0 2025/01/15 07:40:19
0 2025/01/15 07:40:16
Shows the distinct outward splay of the injectors. The hole in the manifold is also angled to accept this angled insertion.
Shows the distinct outward splay of the injectors. The hole in the manifold is also angled to accept this angled insertion.
0 2025/01/15 07:40:11
It turns out shorter hoses are a BAD idea!
It turns out shorter hoses are a BAD idea!
0 2025/01/15 01:08:16
0 2025/01/12 09:37:25
0 2025/01/12 09:36:15
0 2025/01/12 09:33:35
0 2025/01/12 09:18:18
0 2025/01/12 09:13:44