Jaguar Forums - Jaguar Enthusiasts Forum
Replacement connector installed
Replacement connector installed
0 2019/09/30 13:33:47
0 2019/09/30 13:33:56
0 2019/09/30 13:34:05
0 2019/09/30 13:34:17
0 2019/09/30 13:34:29
Fixed it!
Fixed it!
0 2019/09/30 13:36:15
0 2019/10/06 15:02:22
0 2019/10/06 15:08:35
0 2019/10/06 15:12:32
0 2019/10/06 15:13:25
Trying to work the software. Looks straight forward
Trying to work the software. Looks straight forward
0 2019/10/06 15:28:36
0 2019/10/06 15:29:32
0 2019/10/06 15:30:29
0 2019/10/06 15:31:28
0 2019/10/06 15:32:22
New pipes and cats
New pipes and cats
0 2019/10/06 15:36:07
That was scary
That was scary
0 2019/10/06 15:37:40
Smoking from between the upper black piece and the aluminum and also from the lower aluminum to cast iron. Still was a little wet when I removed it
Smoking from between the upper black piece and the aluminum and also from the lower aluminum to cast iron. Still was a little wet when I removed it
0 2019/10/06 15:37:50
Not sure if these can be repaired
Not sure if these can be repaired
0 2019/10/06 15:38:22
This gasket had a larger hole than the original in next pic
This gasket had a larger hole than the original in next pic
0 2019/10/06 15:39:07
Whew!
Whew!
0 2019/10/06 15:48:22
Not sure why I got this. But it seemed to be fixed later on
Not sure why I got this. But it seemed to be fixed later on
0 2019/10/06 15:49:34
It showed weird setups. A manual?
It showed weird setups. A manual?
0 2019/10/06 15:50:30
0 2019/10/06 15:51:37
0 2019/10/06 15:52:57
0 2019/10/08 05:28:21
This is the vacuum line that goes to the fitting at the throttle body elbow. It was leaking slightly. Its grooved so I wet sanded it smooth on both ends so it would seal. It worked!
This is the vacuum line that goes to the fitting at the throttle body elbow. It was leaking slightly. Its grooved so I wet sanded it smooth on both ends so it would seal. It worked!
0 2019/10/10 05:31:40
I ran a vacuum test and had a steady 17inches of vacuum and it behaved well. No bad valves or major leaks
I ran a vacuum test and had a steady 17inches of vacuum and it behaved well. No bad valves or major leaks
0 2019/10/10 05:31:48
Heres where I injected the smoke the second time. You can see the rubber 90 degree elbow on the hard line
Heres where I injected the smoke the second time. You can see the rubber 90 degree elbow on the hard line
0 2019/10/10 05:31:56
Anyone know why the replacement egr lower tube gasket (bottom) has a bigger opening that the original gasket? The tubes hole matches the smaller hole but the replacement has the bigger hole. I want the right gasket. Also does it natter which way its installed?
Anyone know why the replacement egr lower tube gasket (bottom) has a bigger opening that the original gasket? The tubes hole matches the smaller hole but the replacement has the bigger hole. I want the right gasket. Also does it natter which way its installed?
0 2019/10/10 05:32:01
0 2019/10/10 06:16:11
New EGR with sealant around cover
New EGR with sealant around cover
0 2019/10/11 19:09:52
0 2019/10/11 19:09:59
0 2019/10/11 19:10:04
0 2019/10/11 19:10:09
Wrong gasket AJ82340. Right gasket AJ87246
Wrong gasket AJ82340. Right gasket AJ87246
0 2019/10/11 19:10:16
Top tube flange after sanding a lil. You can see the high spots (shiney) outside the bolt holes
Top tube flange after sanding a lil. You can see the high spots (shiney) outside the bolt holes
0 2019/10/11 19:14:39
Lower flange after sanding a bit
Lower flange after sanding a bit
0 2019/10/11 19:14:50
Still more needed
Still more needed
0 2019/10/11 19:15:00
And more
And more
0 2019/10/11 19:15:07