Jaguar Forums - Jaguar Enthusiasts Forum
Wishbone and driveshaft released
Wishbone and driveshaft released
0 2023/02/12 10:02:23
This photo shows the heater return pipe running to the radiator spigot
This photo shows the heater return pipe running to the radiator spigot
0 2023/02/07 23:33:36
0 2023/01/22 22:43:44
0 2023/01/22 22:43:02
0 2022/12/23 09:21:38
0 2022/12/20 00:29:27
0 2022/12/20 00:28:57
0 2022/12/12 07:51:35
0 2022/12/12 07:51:21
0 2022/12/12 07:51:07
0 2022/12/12 07:50:52
0 2022/12/09 08:12:17
0 2022/12/05 05:49:11
0 2022/12/05 05:47:29
0 2022/12/05 00:15:42
0 2022/12/04 22:38:13
0 2022/12/04 22:37:34
0 2022/12/04 22:37:00
This photo shows the 5v solid yellow feed joined to two bullet connectors. These connectots fit into the electrical switch's bullet connectors seen in the background. You can just see the male bullet connector's yellow wire looping round and into the sleeved llom. This goes to the ATS plug.
This photo shows the 5v solid yellow feed joined to two bullet connectors. These connectots fit into the electrical switch's bullet connectors seen in the background. You can just see the male bullet connector's yellow wire looping round and into the sleeved llom. This goes to the ATS plug.
0 2022/12/03 05:13:23
This is what the electrical thermostaic switch look like, it is normally closed until the fuel rail gets hot.
This is what the electrical thermostaic switch look like, it is normally closed until the fuel rail gets hot.
0 2022/12/03 05:12:45
0 2022/11/19 12:13:16
The standard Lucas ECU is fixed just inside the black RHS strengthener bracket, and can partly be see here marked up.
The standard Lucas ECU is fixed just inside the black RHS strengthener bracket, and can partly be see here marked up.
0 2022/10/30 02:47:40
0 2022/10/30 02:43:27
0 2022/10/26 10:32:07
0 2022/10/20 00:58:05
New Anderson Powerpole connector to amplifier to replace old rubber one.
New Anderson Powerpole connector to amplifier to replace old rubber one.
0 2022/10/20 00:51:40
Wirees spliced into emerging dizzy bottom pickup wires. Best to use heat shrink solder connectors for this job.
Wirees spliced into emerging dizzy bottom pickup wires. Best to use heat shrink solder connectors for this job.
0 2022/10/20 00:50:57
My problem
My problem
0 2022/10/20 00:50:18
0 2022/10/18 09:19:21
0 2022/10/18 09:18:43
0 2022/10/18 09:18:01
0 2022/10/18 09:17:21
0 2022/10/14 08:50:12
0 2022/10/12 22:28:10
0 2022/10/08 01:18:36
0 2022/10/08 01:17:40
0 2022/10/08 00:52:53
0 2022/10/08 00:44:54
0 2022/10/07 02:45:09
This shows I the feed pipe going from the pump, via my repositioned filter, to the feed exit in the front lower corner of the trunk (boot for me!). It also shows the fuel line II from the sump tank to the pump. Although your car's siting of these may be different, I think, repeat think, you should find the components doing the same job.
This shows I the feed pipe going from the pump, via my repositioned filter, to the feed exit in the front lower corner of the trunk (boot for me!). It also shows the fuel line II from the sump tank to the pump. Although your car's siting of these may be different, I think, repeat think, you should find the components doing the same job.
0 2022/10/03 07:55:01